Installation Instructions KM 2030, KM 2050 en - CA Installation, repair and maintenance work should be performed by a Miele authorized service technician in accordance with national and local safety regulations and the provided installation instructions.
SAFETY NOTICES FOR INSTALLATION Storage cabinets above the cooktop To avoid damage to the appliance, it present a fire hazard. should not be installed until the This gas cooktop is not authorized upper cabinet and exhaust hood for installation atop have already been mounted.
SAFETY NOTICES FOR INSTALLATION Upper clearance If there are various appliances with different recommended clearance distances beneath the exhaust hood, e. g., a gas stovetop and an electric cooktop, always choose the greatest distance. For an exhaust hood above the appliance, the safe clearance distance indicated by the hood manufacturer must be maintained.
SAFETY NOTICES FOR INSTALLATION When installing a gas stovetop, the cabinetry or walls to ONE side and to the rear of the appliance can be as tall as you wish. However, on the other side there must not be any appliance or 2 ”...
Appliance and installation dimensions KM 2030 a front b Installation height c Gas connection R 1/2" NPT d Junction box with power cable, L = 78 " (2000 mm)
Appliance and installation dimensions KM 2050 a front b Installation height c Gas connection R 1/2" NPT d Junction box with power cable, L = 78 " (2000 mm)
Installation How to make the countertop How to install the gas stovetop cut-out ^ Use the template to make a countertop cut-out. Be sure to observe the minimum distance from the rear wall and from the left or right to a side wall. See the section on "SAFETY NOTICES FOR INSTALLATION".
General installation information Sealing Tiled surfaces The grouting a and shaded area under the cooktop frame must be flat and NEVER use sealing unless it is explicitly even, so that the frame will lie evenly called for in the instructions. The and the sealing strip under the edge of sealing strip under the edge of the the upper part of the appliance can...
Electrical connection This appliance must be grounded This appliance is equipped with a according to local or national codes. three-prong grounding plug to prevent shock hazards. It should be All electrical work should be plugged directly into a properly performed by a qualified electrician grounded outlet.
Gas connection Installation and service must be The gas connection must be made performed by a qualified installer, in accordance with local codes or, service agency or the gas supplier. in the absence of local codes, with This appliance must be installed the National Fuel Gas Code, with its own shut off valve and the ANSI Z 223.1/NFPA 54...
- 4" w.c. LP gas - 10" w.c. Do not use any regulator unless it has been supplied by Miele. Doing so may cause a gas leak. If there is any doubt concerning installation contact the Miele Technical Service Department.
If the appliance is to be connected to a type of gas other than it was originally configured for, both the regulator and burners must be converted. A conversion kit is available as an optional accessory from the Miele Technical Service Department.
36800 10,70 Liquid gas (LP) 26100 7,60 35000 10,20 Rated load at low setting Burner Type of gas KM 2030 / KM 2050 BTU/h Small burner Natural gas (NG) 0,25 Liquid gas (LP) 0,25 Regular burner Natural gas (NG) 1200...
How to switch to a different gas type Switchover to a different gas type should only be performed by a duly authorized gas company technician. Save the nozzles removed from the appliance for future use. Nozzle table If you switch to a different type of gas, the large and small burner nozzles will need to be changed.
How to switch to a different gas type How to change a nozzle Small, normal, and power burners Unplug the appliance from the electrical supply. How to change the main nozzle ^ Remove the burner cover b, the burner ring a (wok) and the burner head c.
How to switch to a different gas type How to change the small nozzles (all burners) To change the small nozzles, you will first need to remove the upper part of the appliance. ^ Unscrew the mounting screws on the burner.
How to switch to a different gas type After switching over ^ Use the reverse order to re-assemble the burner parts. ^ Before putting the upper part of the appliance back in place, light each burner with matches to test the seal on all the gas flow parts.
Help protect our environment Disposal of packing materials Disposal of an old appliance The cardboard box and packing Old appliances contain materials that materials are biodegradable and can be recycled. Please contact your recyclable. Please recycle. local recycling authority about the possibility of recycling these materials.
For the most updated manual, visit the Miele web site.
KM 2030 / KM 2050 en - CA, US M.-Nr. 07 520 080 / 01...