Ubiquiti PowerBridge M3 Quick Start Manual
  1. Manuals
  2. Brands
  3. Ubiquiti Manuals
  4. Network Router
  5. PowerBridge M3
  6. Quick start manual

Ubiquiti PowerBridge M3 Quick Start Manual

Carrier class airmax basestation
Hide thumbs
Table of Contents

Advertisement

Quick Links

Carrier Class
AirMax BaseStation
Models: M3/M365/M5

Advertisement

Table of Contents
loading

Related Manuals for Ubiquiti PowerBridge M3

Summary of Contents for Ubiquiti PowerBridge M3

  • Page 1 Carrier Class AirMax BaseStation Models: M3/M365/M5...

  • Page 3: Package Contents

    Ethernet connections and should be grounded through the AC ground of the PoE. We recommend that you protect your networks from the most brutal environments and devastating ESD attacks with industrial-grade shielded Ethernet cable from Ubiquiti Networks. For more details, visit www.ubnt.com/toughcable...

  • Page 4: Hardware Installation

    PowerBridge Hardware Installation To install the PowerBridge, perform the following steps: 1. Use a flathead screwdriver to unlock the PowerBridge case. Turn the screw counter-clockwise until it is loose. The screw remains attached to the compartment. 2. Lift the cover on the PowerBridge by pressing down and raising it up.
  • Page 5 Hardware Installation 3. Insert the M8X135 Carriage Bolts into the Antenna Bracket Clamps. 4. Connect the Antenna Bracket Clamps to the PowerBridge using the four Serrated Flange Bolts.
  • Page 6 PowerBridge 5. Mount the PowerBridge to the pole by performing the following steps: a. Position the PowerBridge in the desired mounting location on the pole. b. Slide the Pole Bracket Clamps on to the Carriage Bolts. c. Use the four Serrated Flange Lock Nuts to secure the PowerBridge to the pole.
  • Page 7 Hardware Installation 6. Adjust the operating angle of the PowerBridge by adjusting the Serrated Flange Bolts on the top Antenna Bracket Clamp.
  • Page 8 PowerBridge 7. Connect the other end of the Ethernet cable from the PowerBridge to the Ethernet port labeled POE on the PoE Adapter.
  • Page 9 Hardware Installation 8. Connect an Ethernet cable from your LAN to the Ethernet port labeled LAN on the PoE Adapter. 9. Connect the power cord to the power port on the PoE Adapter. Connect the other end of the power cord to a power outlet.

  • Page 10: Installer Compliance Responsibility

    PowerBridge Accessing the AirOS Utility 1. Make sure that your host machine is connected to the LAN that is connected to the PowerBridge. 2. Configure the Ethernet adapter on your host system with a static IP address on the 192.168.1.x subnet (e.g. 192.168.1.100). 3.

  • Page 11: Specifications

    Specifications Specifications PowerBridge M3/M365/M5 Enclosure Size 445 x 416 x 34mm Weight 3.82kg Max Power Consumption 8 Watts Power Supply 24V, 1A surge protection integrated PoE adapter included Power Method Passive PoE (Pairs 4, 5+; 7,8 return) Operating Temperature -30° to 80° C...

  • Page 12: Safety Notices

    PowerBridge Safety Notices 1. Read, follow, and keep these instructions. 2. Heed all warnings. 3. Only use attachments/accessories specified by the manufacturer. WARNING: Do not use this product in location that can be submerged by water. WARNING: Avoid using this product during an electrical storm.

  • Page 13: General Warranty

    Products furnished hereunder shall be free from defects in material and workmanship for a period of one (1) year from the date of shipment by UBIQUITI NETWORKS under normal use and operation. UBIQUITI NETWORKS sole and exclusive...

  • Page 14: Warranty Conditions

    Disclaimer: UBIQUITI NETWORKS does not warrant that the operation of the products is error-free or that operation will be uninterrupted. In no event shall UBIQUITI NETWORKS be responsible for damages or claims of any nature or description relating to system performance, including coverage, buyer’s selection of products for buyer’s application and/or failure of...

  • Page 15: Rf Exposure Warning

    Compliance Compliance Changes or modifications not expressly approved by Ubiquiti Networks, Inc. could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause interference, and 2.
  • Page 16 PowerBridge Des renseignements supplémentaires sur l'exposition aux RF est disponible sur Internet à www.fcc.gov/oet/info/documents/ bulletins CE Marking CE marking on this product represents the product is in compliance with all directives that are applicable to it. Alert sign! Follows CE marking Alert sign must be indicated if a restriction on use applied to the product and it must follow the CE marking.

  • Page 17: Declaration Of Conformity

    UBIQUITI NETWORKS device, megfelel a vonatkozó alapvetõ [Hungarian] követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak. Íslenska Hér me l sir UBIQUITI NETWORKS yfir ví a UBIQUITI NETWORKS device, er í samræmi vi grunnkröfur og a rar kröfur, sem ger ar eru í [Icelandic] tilskipun 1999/5/EC.
  • Page 18 PowerBridge Latviski Ar o UBIQUITI NETWORKS deklar , ka UBIQUITI NETWORKS device, atbilst Direkt vas 1999/5/EK b tiskaj m pras b m un citiem ar to saist [Latvian] tajiem noteikumiem. Lietuviškai UBIQUITI NETWORKS deklaruoja, kad šis UBIQUITI NETWORKS įrenginys atitinka esminius reikalavimus ir kitas 1999/5/EB [Lithuanian] Direktyvos nuostatas.

  • Page 20: Ubiquiti Networks Support

    Phone (9 a.m. - 5 p.m. PST): 408-942-1153 Online Resources Wiki Page: www.ubnt.com/wiki Support Forum: www.ubnt.com/forum Knowledge Base: www.ubnt.com/kb Downloads: www.ubnt.com/support/downloads w w w . u b n t . c o m © 2011 Ubiquiti Networks, Inc. All rights reserved.

This manual is also suitable for:

Powerbridge m5Powerbridge m365

Table of Contents