Summary of Contents for Able-phone AP-5000
- Page 1 AP-5000 Voice Activated Telephone Dialer To contact us: Send us an email to able-phone@juno.com Phone or Fax us at 530-846-7466 Visit us on the web at www.ablephone.com Able Phone 354 Chatfield Avenue Biggs, CA 95917...
-
Page 2: Table Of Contents
A word from us ....................... 3 About this manual ....................3 Chapter One ......................4 Installing Dialer...................... 4 Adding names & numbers ................... 4 Voice dialing ......................5 Erasing a single name ..................6 Erasing all names ....................7 Playback of all names ..................8 Chapter Two ...................... -
Page 3: A Word From Us
A word from us This product is the new successor in the Dialer line of products. Years of experience, market feedback, and use of the latest voice-recognition technology have enabled us to build the most advanced voice-recognition phone dialer in the world. We appreciate your trusting us by purchasing this product, and we wish you a long and enjoyable experience with it. -
Page 4: Chapter One
• Chapter Three answers Frequently Asked Questions, and provides technical details, important notices, and warranty information. Chapter One This chapter describes how to install Dialer, add names, erase a name or all names, listen to stored names, and, most importantly, dial a name using only your voice! Installing Dialer To use Dialer, install it by following these three steps:... -
Page 5: Voice Dialing
B. Choose a quiet moment, when no TV sounds or other background noises are present. Training the unit in a noisy environment will result in poor recognition later. C. Dialer is shipped with a blank memory. Pick up the handset. The unit will play back the main menu. -
Page 6: Erasing A Single Name
your phone will continue to operate normally. The same applies for a power outage. 2. If you are using a cordless phone, please verify that the sound on the line is ‘clean’ with no ‘white’ noises. These ‘white’ noises, usually occur when the mobile part of the cordless phone is far from its base. -
Page 7: Erasing All Names
B. Press the ‘2’ key. Dialer asks for a name to erase. Say the name you wish to erase. C. If the name is found, Dialer asks you to confirm the erasure of the name by pressing the ‘5’ key. [Any other action (for example, hanging up) will cause the name not to be erased.] D. -
Page 8: Playback Of All Names
Playback of all names Whenever needed, you can hear all the names and numbers stored in Dialer’s memory by following these steps: A. Pick up the handset. Dialer asks for a name to call. Press the pound key (#). The main menu will be played. B. -
Page 9: Working With A Speakerphone
by the name "pin". This method can be used in other situations that require dialing a number during a call. Working with a Speakerphone Dialer can be connected and used with a speakerphone. Since working with a speakerphone usually means that the voice signal level coming from the user will be lower then when working with a handset, it is recommended (but not mandatory) that you change Dialer's microphone mode by following these steps:... -
Page 10: Working With A Pbx
Now connect the RC200 to Dialer, as described in Chapter 1 of this manual for any other telephone. Please note that, if you wish to add names, you will be required to use the RC200 keypad. To place a call, give the remote control a short press and wait for Dialer to ask you for a name to call. -
Page 11: Frequently Asked Questions
This chapter answers Frequently Asked Questions and provides technical details, important notices, and warranty information. Frequently Asked Questions The following is a list of the most common questions and problems encountered when using Dialer. If you cannot find a solution to your problem here, please do contact us. - Page 12 Question: Dialer now speaks in a language I do not understand. How can I change it back to my desired language? Answer: Pick up the handset. Press the pound key (#) to reach the main menu. When you do, press the ‘0’...