Wireless Lan - Pioneer BDP-180 Operating Instructions Manual

Wireless LAN

09
Problem
Network cannot be accessed
via wireless LAN.
Cannot connect with the
Miracast/Wi-Fi Direct
function.
There is a connection on the
mobile device but the mobile
device video is not displayed
on the TV (Miracast function).
56
En
Check
This unit and wireless LAN
router etc. are too far apart, or
there is an obstacle between
them.
There is a microwave oven or
other device generating
electromagnetic waves near
the wireless LAN
environment.
Multiple wireless devices are
connected to the wireless
LAN router.
Connection settings between
the unit and the wireless LAN
router etc. are not set up
correctly.
The IP address settings for
the unit and the wireless LAN
router etc. (including DHCP
settings) do not match.
The access point is set to
conceal the SSID.
The access point's security
settings use WEP 152-bit
length code key or shared key
authentication.
Is the Miracast/Wi-Fi Direct
Mode screen displayed on
the TV or is [READY]
displayed on the unitís
display window?
Check the SSID and
password in the Miracast/Wi-
Fi Direct Mode screen.
Is the mobile device
compliant with Wi-Fi Direct
or Miracast?
Is the mobile device
compliant with Miracast?
Remedy
Improve the wireless LAN environment by taking steps such as moving
the unit and wireless LAN router etc. closer together.
• Use the unit in a place away from microwave ovens or others device
generating electromagnetic waves.
• Avoid using devices generating electromagnetic waves as much as
possible when using the unit with a wireless LAN.
When connecting multiple wireless devices, their IP addresses must be
changed.
If the connection settings between the unit and the wireless LAN router
etc. are not set up correctly, connection settings much be performed in
order to connect the unit and the wireless LAN router etc.
• Check the IP address settings of the unit and the wireless LAN router
etc. (including the DHCP setting).
• If the unit's DHCP setting is on, turn the unit's power off, then turn
the power back on. Check that the IP address of the unit matches the
settings of the wireless LAN router etc.
• If the unit's DHCP setting is off, set an IP address matching the
network of the wireless LAN router etc.
For example, if the wireless LAN router's IP address is "192.168.1.1", set
the unit's IP address to "192.168.1.XXX" (*1), the subnet mask to
"255.255.255.0", and the gateway and DNS to "192.168.1.1".
(*1) Set the "XXX" in "192.168.1.XXX" to a number between 2 and 248
that is not assigned to other devices.
In this case, the SSID may not be displayed on the access point list
screen. If not, set the SSID etc. by setting the wireless LAN settings on
the receiver manually.
The unit does not support WEP 152-bit length code key or shared key
authentication.
RETURN
Press on the remote control to close the Miracast/Wi-
Fi Direct Mode Screen. Then press Miracast and perform the controls
again from the Miracast/Wi-Fi Direct Mode Screen.
If an update was performed in the Wi-Fi Direct Mode screen or the unit
was restored to the default settings, the SSID and password will have
changed.
Enter the newly set SSID and password on the mobile device.
Only mobile devices that are compliant with Wi-Fi Direct or Miracast
are supported.
Ask the manufacturer of the corresponding device whether the mobile
device is compliant with Wi-Fi Direct or Miracast.
Select [Refresh] on the Miracast/Wi-Fi Direct Mode screen and then try
connecting again.
• Turn off power (to stand-by mode) once then turn power back on.
• Insert a thin rod into the reset button on the front side of the main
body then reset the unit.
Only mobile devices that are compliant with Miracast are supported.
Ask the manufacturer of the corresponding device whether the mobile
device is compliant with Miracast.