Kenwood KCD-BT6544U/UY Service Manual page 16

KDC-BT6544U/BT6544UY
/BT7043U/BT742U
■ Audio-related test mode
Procedure
Enter the audio adjustment mode (The default items shown are different from model with DSP to model without DSP)
[Model with DSP] (Destination "K" and "E")
When DUAL ZONE is ON: BYPASS→DUAL ZONE→FADER→BALANCE→R-VOLUME→V-OFFSET
When DUAL ZONE is OFF: BYPASS→DUAL ZONE→FADER→BALANCE→SUB-W→V-OFFSET
■ TEL/TI/AUTO [Model without DSP] (Destination "M")
When DUAL ZONE is ON: DUAL ZONE→FADER→BALANCE→BASS→MID→TRE→R-VOLUME→B.BOOST→
USER→HPF-F→HPF-R→V-OFFSET
When DUAL ZONE is OFF: DUAL ZONE→FADER→BALANCE→BASS→MID→TRE→SUB-W→B.BOOST→
USER→HPF-F→HPF-R→LPF-SW→V-OFFSET
About audio adjustment items (include both Audio Function Mode and Audio Setup Mode)
Procedure
BYPASS *1 (Only in model with
DSP)
Dual Zone
Fader
For item
Balance
forwarding
R-VOLUME
procedure,
Bass Level
press [AUD]
key and
Middle Level
[FM] key
Treble Level
HPF Front (KDC-BT7043U only)
HPF Rear (KDC-BT7043U only)
For item
LPF Subwoofer
forwarding
LPF Subwoofer Phase
procedure,
(KDC-BT7043U only)
press [AUD]
key and Volume Offset
[FM] key
Bass BOOST
*1: Display the settings for "BYPASS ON/OFF" in the AUDIO adjustment mode of the test mode to enable the selection opera-
tion. These settings are same as the BYPASS settings of DSP setting in the multi-function.
■ [ATT] key operation
Press [ ] key briefl y in the Tuner source.
■ MENU-related test mode
* In the TUNER source, run the unit in the normal operation (PRESET call operation) mode.
Press [SEARCH] key briefl y (Unit itself)
Press [DNPP/SBF] key and [DIRECT] key briefl y (Remote controller)
16
TEST MODE
Item
[VOL] knob and [
[VOL] knob and [
[VOL] knob and [
[VOL] knob and [
[VOL] knob and [
[VOL] knob and [
[VOL] knob and [
[VOL] knob and [
[VOL] knob and [
[VOL] knob and [
[VOL] knob and [
[VOL] knob and [
[VOL] knob and [
[VOL] knob and [
Procedure
Procedure
Note
Procedure
/ ] key BYPASS ↔ THROUGH (Default value: BYPASS)
/ ] key Adjust to 2 steps of OFF ↔ ON. (Default value: OFF)
/ ] key Adjust to 3 steps of R15 ↔ 0 ↔ F15. (Default value: 0)
/ ] key Adjust to 3 steps of L15 ↔ 0 ↔ R15. (Default value: 0)
/ ] key Adjust to 2 steps of 0 ↔ 35. (Default value: 35)
/ ] key Adjust to 3 steps of -8 ↔ 0 ↔ +8. (Default value 0)
/ ] key Adjust to 3 steps of -8 ↔ 0 ↔ +8. (Default value 0)
/ ] key Adjust to 3 steps of -8 ↔ 0 ↔ +8. (Default value 0)
Adjust to 2 steps of Through ↔ 180Hz.
/ ] key
(Default value: Through)
Adjust to 2 steps of Through ↔ 180Hz.
/ ] key
(Default value: Through)
Adjust to 2 steps of 60Hz ↔ Through.
/ ] key
(Default value: Through)
Adjust to 2 steps of Normal ↔ Reverse.
/ ] key
(Default value: Normal)
/ ] key Adjust to 2 steps of -8 ↔ 0 . (Default value 0)
/ ] key Adjust to 2 steps of OFF ↔ ON . (Default value OFF)
ATT OFF/ON
Continuous forwarding by remote control is prohibited
Description
Note
Note