Kemppi Minarc 120AU Operating Manual
Hide thumbs
Also See for Minarc 120AU:
- Operating manual (22 pages) ,
- Operating instructions manual (11 pages)
Table of Contents
Advertisement
Minarc
150, 151
150 VRD
120 AU, 150 AU
Operating manual • English
Bruksanvisning • Svenska
Bruksanvisning • Norsk
Brugsanvisning • Dansk
Gebrauchsanweisung • Deutsch
Gebruiksaanwijzing • Nederlands
Manuel d'utilisation • Français
Manual de instrucciones • Español
Instrukcja obsługi • Polski
Инструкции по эксплуатации • По-русски
EN
FI
Käyttöohje • Suomi
SV
NO
DA
DE
NL
FR
ES
PL
RU
Advertisement
Table of Contents
Related Manuals for Kemppi Minarc 120AU
Summary of Contents for Kemppi Minarc 120AU
- Page 1 Minarc 150, 151 150 VRD 120 AU, 150 AU Operating manual • English Käyttöohje • Suomi Bruksanvisning • Svenska Bruksanvisning • Norsk Brugsanvisning • Dansk Gebrauchsanweisung • Deutsch Gebruiksaanwijzing • Nederlands Manuel d’utilisation • Français Manual de instrucciones • Español Instrukcja obsługi •...
- Page 3 Operating Manual english...
-
Page 4: Table Of Contents
COntents preFaCe ......................... General .......................... Product introduction .................... BeFOre yOu start using the unit ....... Unpacking ........................Placing the unit ......................Serial number ......................Main components ....................Distribution network ..................... Connecting to power supply mains ............. Filler materials and equipment ............... -
Page 5: Preface
For your own safety and that of your working environment, pay particular attention to the safety instructions in the manual. For more information on Kemppi products, contact Kemppi Oy, consult an authorised Kemppi dealer, or visit the Kemppi web site at www.kemppi.com. -
Page 6: Product Introduction
Kemppi Minarc is a manual metal arc welding machine, small in size, suitable for industry, site and repair welding. The unit uses one phase connection voltage and it is manufactured for two different mains voltages: 230 V (Minarc 150) and 110 V (Minarc 151). -
Page 7: Serial Number
serial nuMBer Serial number of the unit is marked on the rating plate of the unit. The serial number makes it possible to trace product manufacturing series. You might need the serial number when placing spare parts orders or when planning maintenance. -
Page 8: Distribution Network
distriButiOn netwOrk All regular electrical devices without special circuits generate harmonic currents into distribution network. High rates of harmonic current may cause losses and disturbance to some equipment. Minarc 150, 150 Vdr, 120 au, 150 au WARNING: This equipment does not comply with IEC 61000-3-12. If it is connected to a public low voltage system, it is the responsibility of the installer or user of the equipment to ensure, by consultation with the distribution network operator if necessary, that the equipment may be... -
Page 9: Use
NOTE! It is forbidden to weld in places where there is a danger of fire or explosion! welding prOCesses 3.1.1 Manual Metal arc welding (MMa) In manual metal arc (MMA) the welding filler material is melted from the electrode to the weld pool. Rate of welding current is selected on the basis of electrode size used and welding position. -
Page 10: Operating Functions
Operating FunCtiOns See also 2.4. Main components and 3.4. Welding selections. Signal light, machine 'ON' , (VRD: 'VRD safe ON') Welding process selecting switch Welding current adjuster Signal light for overheating Suitable electrodes; reference values for welding current Main switch and signal light When you turn the main switch to position I, signal light is lit and the unit is ready for welding. -
Page 11: Welding Selections
welding process selector, MMa / tig Switch is used for selecting either MMA or TIG welding, depending on welding target. VRD: When you have switched the unit to TIG welding, VRD is constantly active, thus reducing terminal voltage to 30 V. This facilitates arc cut-off when you stop welding. -
Page 12: Welding Selections
welding seleCtiOns NOTE! Welding fumes may be dangerous to your health, see that there is ample ventilation during welding! Never look at the arc without face shield made for arc welding! Protect yourself and your surroundings from the arc and hot spatter! 3.4.1 earthing If possible, always fix earth cable clamp directly on the welding piece. -
Page 13: Maintenance
• Check the mains cable and plug. Poor welding result Several factors affect the welding quality. • Check that the earthing clamp is firmly attached, the point of attachment is clean and that the cable and its connectors are intact. • Check that the shielding gas flows out of the torch tip. • Check that the electric voltage is not irregular or too low/high. Overheating indicator lit The device has overheated. • Ensure that cooling air has unrestricted flow. • If the machine’s duty cycle has been exceeded, wait for indicator to turn off. • Too low or high supply voltage. If the machine’s malfunction is not eliminated with these measures, contact KEMPPI service. -
Page 14: Disposal
The owner of the equipment is obliged to deliver a decommissioned unit to a regional collection centre, per the instructions of local authorities or a Kemppi representative. By applying this European Directive you will improve the environment and human health. -
Page 15: Technical Data
teChniCal data Minarc 150, 150 VRD Minarc 151 Connection voltage 1 ~ phase 50/60 Hz 230 V ± 15 % 110 V ± 15 % Rated power at max. current 35 % ED MMA 140 A/7.5 kVA 140 A/7.5 kVA 100 % ED MMA 100 A/5.1 kVA 100 A/5.1 kVA 35 % ED TIG 150 A/5.0 kVA 150 A/5.0 kVA... - Page 16 Minarc 120AU Minarc 150AU Connection voltage 1 ~ phase 50/60 Hz 240 V + 10 % ... - 20 % 240 V + 10 % ... - 20 % Rated power at max. current ED MMA 50 %, 110 A/5.5 kVA 35 %, 140 A/7.5 kVA ED MMA 100 %, 80 A/3.9 kVA 100 %, 100 A/5.1 kVA ED TIG 50 %, 120 A/3.5 kVA 35 %, 150 A/5.0 kVA ED TIG 100 % ,80 A/2.2 kVA 100 %, 110 A/3.3 kVA Supply current 35 % ED I...
- Page 18 ул. Полковая 1, строение 6 Kotimaan myynti: 127018 Москва KEMPPI FRANCE S.A.S. Tel +358 3 899 11 Tel +7 495 739 4304 65 Avenue de la Couronne des Prés Telefax +358 3 734 8398 Telefax +7 495 739 4305 78681 EPONE CEDEX myynti.fi@kemppi.com info.ru@kemppi.com FRANCE Tel +33 1 30 90 04 40 KEMPPI SVERIGE AB KEMPPI, TRADING (BEIJING) COMPANY, Telefax +33 1 30 90 04 45 LIMITED Box 717 sales.fr@kemppi.com Room 420, 3 Zone, Building B, S-194 27 UPPLANDS VÄSBY No.12 Hongda North Street, SVERIGE KEMPPI GmbH Beijing Economic Development Zone, Tel +46 8 590 783 00 Otto-Hahn-Straße 14 100176 Beijing Telefax +46 8 590 823 94 D-35510 BUTZBACH CHINA sales.se@kemppi.com...