Using Your Coffeemaker To Dispense Hot Water - Wolfgang Puck BIFCM010 User Manual

Using Your Coffeemaker (Cont.)
3 Put the coffee basket; loaded with coffee grounds; into the coffee
basket holder and fit the coffee basket holder to the coffeemaker,
making sure that it is fully inserted and that the handle is fully closed
and latched. This ensures that the unit is correctly sealed.
4
Place the carafe on the Keep Warm plate. For individual cups,
depending on size place on stand, or directly on keep warm plate.
Please note, the Keep Warm setting does not work in Cup mode. or
cup on the keep-warm plate.
5
Plug the power cord into the outlet electricity and press START/
STOP button once. The LCD will display the default setting
mentioned on page 8 (See DEFAULT SETTING), the blue backlight
will be illuminated while the appliance is in use.
6 If WATER mode is displayed, press the COFFEE/WATER mode
button to select COFFEE.
7 Select the required cup or carafe mode by pressing the Cup Select
or Carafe Select button, then select the required volume by pressing
the Up Arrow or Down Arrow buttons.
8
The display will show the previous coffee strength selected for that
volume. If you want to change the coffee strength, press the Coffee
Strength button, then press the Up Arrow or Down Arrow buttons
to change. The strength will be remembered only for the selected
volume. If you change volume, you may need to change the strength
again.
9 Press START/STOP button again to start the coffee making.
The process will start immediately but you will notice a short delay
while the hot water is flowing into the coffee basket. Then the coffee
will start to flow. It may seem too strong but don't worry – in this
first stage, the coffeemaker is making the perfect extraction of your
coffee grounds for the volume and strength that you have selected.
It finishes this stage by forcing any remaining liquid out of the
coffee basket with pressure before switching to the second stage of
'bypass', in which the hot water goes directly to your cup or carafe
without passing through the coffee grounds. The proportion of hot
water passing through the coffee to the amount of water bypassing
varies with the selected strength and the selected volume. This
intelligent bypass system ensures that any volume or strength of
coffee can be produced without over or under extraction.
10 At the end of the total brewing cycle, you will hear 2 short beeps to
indicate that the coffee is ready to drink.
Note: The coffee will not be ready until the end of the total brewing
cycle, including the coffee stage and the water bypass stage because
the coffee will not have reached the selected strength or volume.
Removing the cup or carafe will not stop the cycle and will result in
spillage of coffee or water.
You can stop the appliance at any time by pressing the START/STOP
button but this will cancel the cycle. Pressing again will start another
cycle from the beginning and could spoil the coffee.
10
Using Your Coffeemaker to
Dispense Hot Water
Hot Water Dispense
1 Open the water tank lid and fill the water tank with potable coffee/
water.
2 The water level should not exceed the MAX level marked in water
gauge. Then close the water tank lid. Note: The coffee brew basket
and holder do not need to be in place for hot water dispense as they
will be bypassed completely. If they are already in place, it doesn't
matter.
3
Place the carafe or cup on the keep-warm plate.
4
Plug the power cord into the outlet and press START/STOP button
once. The LCD will display the default setting mentioned on page 8
(See DEFAULT SETTING), the blue backlight will be illuminated while
the appliance is in use.
5 If coffee mode is displayed, press the COFFEE/WATER Select button.
6 Select the required cup or carafe mode by pressing the Cup Select or
Carafe Select button, then select the required volume by pressing the
Up Arrow or Down Arrow buttons.
Keep Warm Function
In carafe mode only, keep-warm can be selected to keep the brewed
coffee at the right temperature for drinking. Keep-warm is activated by
pressing the Keep-warm button either before starting the brew cycle or
at any time during the brew cycle. It cannot be activated after the brew
cycle has finished.
Keep-warm can be de-activated by pressing the keep-warm button again
but it cannot be re-activated if the brew cycle has already finished. If it is
not manually de-activated, keep-warm will automatically switch off after
2 hours. During keep-warm activation, the START/STOP button will flash
red.
11