Subscribe to Our Youtube Channel
Related Manuals for Meyer Sound MTS-4
Summary of Contents for Meyer Sound MTS-4
-
Page 1: Operating Instructions
Operating Instructions MTS-4 Self-Powered Full-Range Loudspeaker Patents Pending Copyright © 1997, Meyer Sound Laboratories, Inc. All rights reserved Part #: 05.029.006.01 Rev B... -
Page 2: Declaration Of Conformity
6 sides Berkeley, California USA Vibration: 10 – 55 Hz (0.010 m October 1, 1995 peak-to-peak excursion) Made by Meyer Sound, Berkeley, CA, USA U U L L U U L L LISTED European Office: Meyer Sound Germany 3K59 ®... -
Page 3: Table Of Contents
R e m o t e M o n i t o r i n g S y s t e m Meyer Sound, Berkeley, CA. USA System panel (if RMS is installed) Rear User Panel shown with the optional... -
Page 4: Introduction
Windows-based PC. Contact Meyer Sound for more If the MTS-4 shuts down due to either low or high volt- information about RMS. age, the power supply automatically turns on after three seconds if the voltage has returned to either normal operating range. -
Page 5: Current Requirements
Current Requirements Safety Issues The MTS-4 presents a dynamic load to the AC mains Pay close attention to these important electrical and which causes the amount of current to fluctuate between safety issues. quiet and loud operating levels. Since different types of... -
Page 6: Power Connector Wiring Conventions
• Connect the blue wire to the terminal marked Each driver in the MTS-4 is powered by one channel of with an N or colored black. the Meyer MP-4, a four-channel 2480 W amplifier •... -
Page 7: Fans And Cooling System
85 ° C, the MTS-4 automatically shuts down until AC power is removed and reapplied. If the MTS-4 shuts NOTE: Although the TPL limiters exhibit smooth sonic... -
Page 8: Rigging
Rigging Measurement and System Integration Tools The MTS-4 weighs 280 lb (127 kg). The maximum recom- mended load for a single cabinet with aircraft pan fittings It is essential that even the most carefully assembled is 600 lb (273kg). This working load is based on a 5:1 safety sound systems be analyzed with precise measurement factor. -
Page 9: Complete Systems
Combining the PSW-4 with the MTS-4 doubles the low • ¿¿ Set the CQ to the opposite polarity to the MTS-4 frequency power of the system because both loudspeakers to phase align the mid-hi frequencies and mini- contain the same sub and low drivers. -
Page 10: Driver Troubleshooting
The TPL LED can indicate serious driver problems, if interpreted correctly. If one MTS-4 in a system exhibits NOTE: Since polarity reversal causes excessive driver substantially more TPL activity than others receiving... -
Page 11: Array Design
(LF) addition compared to a single requirements, contact Meyer Sound to obtain additional MTS-4. Due to the larger distance between LF drivers in information on array design. V, compared to H arrays, the V coverage narrows at a faster rate than does the H coverage for H arrays, given the same array size and adjacent speaker placement. - Page 12 MTS-4 Array Coverage and Maximum SPL Number of Horizontal MTS-4s @ Angle 2 @ 15° 2 @ 30° 2 @ 45° 3 @ 15° 3 @ 30° 3 @ 45° Coverage Max Peak Coverage Max Peak Coverage Max Peak Coverage...
-
Page 13: Safety Summary
Safety Summary English Français • To reduce the risk of electric shock, disconnect the loud- • Pour réduire le risque d’électrocution, débranchez la prise speaker from the AC mains before installing audio cable. principale de l’haut-parleur, avant d’installer le câble Reconnect the power cord only after making all signal d’interface allant à... -
Page 14: Specifications
Specifications Acoustical ± 3 dB 30 Hz – 16 kHz; –6 dB at 26 Hz and 18 kHz Frequency Response ± 70° 90 Hz – 17.2 kHz Phase Response Maximum Peak SPL 140 dB Dynamic Range > 110 dB Coverage 70°...
Need help?
Do you have a question about the MTS-4 and is the answer not in the manual?
Questions and answers