Page 1
Total Access 900e Series Hardware Installation Guide Total Access 908e Total Access 916e Total Access 924e 64240916L1-34D November 2006...
Page 2
Total Access® is a registered trademark of ADTRAN, Inc. To the Holder of the Manual The contents of this manual are current as of the date of publication. ADTRAN reserves the right to change the contents without prior notice. In no event will ADTRAN be liable for any special, incidental, or consequential damages or for commercial losses even if ADTRAN has been advised thereof as a result of issue of this publication.
Page 5
Advance notification and the opportunity to maintain uninterrupted service are given. 4. If experiencing difficulty with this equipment, please contact ADTRAN for repair and warranty information. The telephone company may require this equipment to be disconnected from the network until the problem is corrected or it is certain the equipment is not malfunctioning.
Page 7
Class A prescrites dans la norme sur le materiel brouilleur: “Appareils Numériques,” NMB-003 edictee par le ministre des Communications. Service and Warranty For information on the service and warranty of ADTRAN products, visit the ADTRAN website at http://www.adtran.com/support. 64240916L1-34D...
(management interface). An optional battery backup is also available for the Total Access 900e Series. The last two digits of the product name indicate the number of on-board FXS ports. The Total Access 908e contains 8 FXS ports, the Total Access 916e contains 16 FXS ports, and the Total Access 924e contains 24 FXS ports or 16 FXS ports plus 8 FXO ports with octal FXO daughter board.
After unpacking the unit, inspect it for possible shipping damage. If the equipment has been damaged in transit, immediately file a claim with the carrier and contact ADTRAN Customer and Product Service (refer to Warranty and Customer Service and Product Support Information, on page 10).
PHYSICAL DESCRIPTION Reviewing the Front Panel Design Figure 1 shows the Total Access 908e which contains 8 FXS ports. Figure 1. Total Access 908e Front Panel Layout Figure 2 shows the Total Access 916e front panel which contains 16 FXS ports.
T1 0/3 T1 0/4 PRI/CAS Figure 4. Total Access 908e, 916e, 924e Rear Panel Layout Rear Panel Interfaces and LEDs Power Supply The Total Access 900e Series products have a 90 to 125 VAC power supply with an IEC connector.
Receptacle Figure 5. Voice Connector Pin Assignments The Total Access 908e only uses circuits 1 through 8. The Total Access 916e only uses circuits 1 through 16. The Total Access 924e uses all circuits (1 through 24), and the FXO interfaces are on circuits 17 through 24.
IP network. Instructions on how to access the Web-based GUI are given in the Web GUI Configuration Guide, document number 61210916L1-42.1 and on the Quick Start Guide, document number 61210916L1-13 (provided on the ADTRAN OS System Documentation CD).
The Total Access 900e Series products mount and connect with standard fasteners and hand tools. ADTRAN recommends 1U (1.75 inches) of separation above and below the Total Access 900e Series unit. This spacing allows the unit to dissipate heat. The design of the Total Access 900e Series uses the chassis to distribute heat generated by the unit’s...
Total Access 900e Series Hardware Installation Guide Battery Backup Unit BATTERY BACKUP UNIT The ADTRAN Battery Backup Unit (BBU) is an optional device designed as a backup DC power supply for the Total Access 900e Series. Total Access 900e Series BBU (P/N 1175044L1/L2) The BBU connects to the Total Access 900e Series through a 6-foot charge/discharge, 2-conductor wire with a keyed modular plug (included with the BBU).
Total Access 900e Series Hardware Installation Guide Battery Backup Unit Safety Notices The Battery Backup Unit should only be used in specified ADTRAN applications. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: •...
Need help?
Do you have a question about the Total Access 908e and is the answer not in the manual?
Questions and answers