Related Manuals for Invacare top end pro 2 all sport
Summary of Contents for Invacare top end pro 2 all sport
-
Page 1: Assembly Instructions
Assembly Instructions Invacare® Top End® Pro™-2 All Sport Wheelchair Part #: 1181409 Be sure to record your serial number and read the owners manual. Rev: A... - Page 2 What you will receive Box includes: Seat frame Complete wheel assemblies Base frame Seat frame(assembled w/ side guards, upholstery, cushion, and frame protector) Footrest Base Frame Axles Adjustable anti-tip assembly Positioning strap All attaching hardware.
- Page 3 Tools you will need: Adjustable wrench 5mm allen wrench 4mm allen wrench Two 10 mm combination wrenches or socket 7/16 and ¾ inch wrench An assistant may also be helpful to hold frame in place while installing seat frame Entire assembly should take about 30-45 minutes ...
- Page 4 Step one – Adjusting and installing wheels Adjust the nut on the axle receiver. The axle receiver nut will be loosely installed on the axle receiver bolt, this nut will need to be tightened down with the adjustable wrench. Adjust the nut on the actual axle so that the ball bearing locks into place when put through the wheels and inserted into axle receiver.
- Page 5 Step two – Installing anti-tip Install adjustable anti-tip wheel. Release and loosen the quick release lever attached to the anti-tip clamp Insert adjustable anti-tip into base frame, with wheel facing down. With rear wheels still on tighten quick release lever with anti-tip at level desired (should be about a fingers width off the ground) ...
- Page 6 Step three – Attaching the L brackets There will be L brackets and curved brackets The L brackets are for the front, and curved for the rear The L brackets attach with the bolts that are bagged with 4 bolts that are all the same ...
- Page 7 Step three – continued (L brackets) Attach the L brackets to the inside of the welded tabs on the seat frame. Insert the bolt from the inside of the seat frame (use one flat washer, one split washer, and one nut for each bolt.
- Page 8 Step four – Curved brackets Attach the curved brackets to the inside of the welded tabs on the seat frame. » You will want to take the larger bolts out of the bag and set them aside(these are extras and will not be used on the chair, use the two smaller bolts in the hardware bag to attach each curved bracket to the chair.
- Page 9 Step four - continued Be sure to leave the brackets slightly loose, so that they can be adjusted and attached to the base frame...
- Page 10 Step five – Attach seat frame to base frame Take seat frame and place it on top of the base frame, with the brackets lined up to the tabs welded in the rear and the holes drilled in the frame on the front. ...
- Page 11 Step five – continued (front L brackets) Place flat and a coped washer on each bolt then put the bolt through the drilled hole in the front of the frame(make sure the head of the bolt is on the inside of the frame), place the second coped washer on the inside of the frame and then place base frame on top and secure in the position desired.
- Page 12 Step Six – Attaching the curved brackets Adjust the seat frame so that the curved bracket is in the position and height desired. Use the bolts, as well as a washer, and a nut to attach and secure the curved bracket in place, again, make sure the head of the bolt is installed on the inside of the frame.
- Page 13 Step Seven – footrest Use the two-part clamps and 4 bolts. Assemble the clamps as seen in picture below. Place the larger side of the clamps around the base frame down tube in the position desired. Put the other side of the clamp around the footrest and tighten using allen key. ...
- Page 14 Step Eight – Calf strap and seat belt Attach foot strap around front down tubes in desired position. Attach seat belt strap around the back frame in desired location. (we suggest putting the strap through the sideguard for secure attachment.
- Page 15 15”, and the second can be removed making the chair 13” deep. A new cushion will need to be purchased, or the current one modified, to accommodate the change in seat depth. Call Customer service with any questions, 1-800-532-8677 or email us at Topendorders@Invacare.com.
- Page 16 If you have any questions you can call customer service at 1-800-532-8677 ©2015 Invacare Corporation. All rights reserved. Trademarks are identified by the symbols ™ and ®. All trademarks are owned by or licensed to Invacare Corporation unless otherwise noted. Form 15-195 151074.