Sony HBD-E570 Service Manual page 5

QQ
3 7 63 1515 0
CAPACITOR ELECTRICAL DISCHARGE PROCESSING
When checking the board, the electrical discharge is necessary for
the electric shock prevention.
Connect the resistors referring to the fi gure below.
• MAIN board (C3115, C3125, C3215, C3315, C3415, C3425)
Both ends of CN3001.
– MAIN Board (Conductor Side) –
• POWER board (C903, C932, C933)
Both ends of respective capacitors.
– POWER Board (Conductor Side) –
TE
L 13942296513
800 /2 W
NOTE OF REPLACING THE OPTICAL DEVICE (KEM-
460AAA) OR MB-134 BOARD
Optical device (KEM-460AAA) for BD requires precise read out
functions and secure contents protection system for more than past
DVD/CD.
Therefore, in the case repaired as follows, the writing work of the
OP data is necessary.
• When the optical device (KEM-460AAA) is replaced (The
MB-134 board doesn't replace).
• When both the optical device (KEM-460AAA) and MB-134
board are replaced.
• When the MB-134 board is replaced (The optical device
(KEM-460AAA) doesn't replace) (In this case, do the work of
"3. Optical device (KEM-460AAA) replacement" other than
the replacement of new optical device).
Note: The servo adjustment is done while writing the OP data. The manual
adjustment is unnecessary.
LD ON TIME history doesn't carry over.
Do not touch any optical block parts, turn table and during replac-
ing. BD laser diode is very sensitive.
www
.
http://www.xiaoyu163.com
800 /2 W
C3415
C3215
C3315
C3425 C3125
800 /2 W
C903
C932 C933
800 /2 W
x ao
y
i
http://www.xiaoyu163.com
8
1. Preparation
1-1. ESD Countermeasure
It is necessary to confi rm the state of static electricity in the work
space before the repair is started.
The static electricity resistance of the BD laser is weaker than that
of the DVD/CD laser.
Do work space and worker's ESD countermeasures to prevent de-
struction by ESD.
4
1-2. Jig
1 • Digital camera (Recommend with macro mode)
CN3001
• USB memory
• PC
• Barcode decoder (Refer to "1-3. Barcode decoder
(BDBUDEC)")
C3115
1-3. Barcode decoder (BDBUDEC)
Part No. : J-6090-212-A
Jig name : BDBUDec.exe
Release : 2009.02.19
Version : 1.0.0.0
Software contents :
• BDBUDec.exe
• SavePath.ini
• TasmanBars.dll : Decode dll
• Uninst.exe
Install procedure:
1. Unzip the barcode decoder fi les to any PC folder.
2. Check the taken barcode photo click & drop onto "BDBUDec.
Q Q
3 6 7 1 3
exe".
When the barcode decoder is used for the fi rst time, the pass-
word is necessary. It is unnecessary since the second times.
Note 1: The password will be supplied to only service headquarters, and
service center name/q'ty/all of software registered information
should be maintained by service headquarters.
Note 2: Do not change the decoded fi le name "BuData.txt".
3. When ".NET frame work requirements" is displayed, down-
load following applications from Microsoft download site.
• Microsoft .NET Framework Version 2.0 Redistributable Pack-
age (x86)
http://www.microsoft.com/downloads/details.aspx?displaylan
g=en&FamilyID=0856eacb-4362-4b0d-8edd-aab15c5e04f5
• Microsoft .NET Framework 2.0 Service Pack 1 (x86)
http://www.microsoft.com/downloads/details.aspx?displaylan
g=en&FamilyID=79bc3b77-e02c-4ad3-aacf-a7633f706ba5
u163
.
HBD-E370/E470/E570/E870/T57
2 9 9 4 2 8
: Barcode decoder software
: Decoded fi le destination setting fi le (Ini-
tial destination is "C:\BuData.txt")
: Uninstall the "BDBUDec.exe" from PC
1 5 0 5 8 2 9 9 4
m
co
9 9
2 8 9 9
5