1. Manuals
  2. Brands
  3. Serpent Manuals
  4. Motorized Toy Car
  5. Spyder SR X4
  6. Instruction manual & reference manual

Serpent Spyder SR X4 Instruction Manual & Reference Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
INSTRUCTION MANUAL
& REFERENCE GUIDE

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Spyder SR X4 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Serpent Spyder SR X4

Summary of Contents for Serpent Spyder SR X4

  • Page 1 INSTRUCTION MANUAL & REFERENCE GUIDE...
  • Page 2 Spyder. These exploded views show the standard parts of a particular assembly step The Serpent Spyder offers state of the art specifications and leads the way in 1/10 along with the Serpent part number. buggy design, using all the knowledge we have gathered since 1980.
  • Page 3 Read this first! - Before operating this car, always check - This is a highly technical hobby product, the mechanical status of the car. Also intended to be used in a safe racing environment. check that the transmitter and receiver This car is capable of speeds in excess of 80 frequencies correspond and are not used km/h or 50mph.
  • Page 4 FRONT DIFFERENTIAL ASSEMBLY Use some grease STEP NOTE: during assembly In step 5 & 6 to mount the pin, first put the pin 1.5x8 in the purpose made slot as shown, and after slide it through the hole in the FRONT shaft.

  • Page 5: Rear Differential Assembly 4

    REAR DIFFERENTIAL ASSEMBLY Use some grease STEP NOTE: during assembly In step 5 & 6 to mount the pin, first put the pin 1.5x8 in the purpose made slot as shown, and after slide it through the hole in the REAR shaft.

  • Page 6: Rear Transmission Assembly 7

    REAR TRANSMISSION ASSEMBLY STEP DIFF HEIGHT SETTING: Change the indicated inserts to move the diff up or down. HIGH DOWN 5x10x4 10x15x4 Default setup STEP 10x15x4 5x10x4 M2.5X12 STEP M3X15 M3X10 M3X10 M3X15 Page...
  • Page 7 MID TRANSMISSION ASSEMBLY STEP STEP Nylock nut M3 5x8x2.5 STEP 12x18x4 5x10x4 STEP 5x13x4 5x8x0.1 5x10x4 Page...
  • Page 8 STEP M3X8 M3X30 STEP M3X30 M3X30 STEP M3X35 Page...
  • Page 9 2X12 STEP NOTE: Place belt onto rear top STEP shaft pulley and roll belt onto front slipper pulley INITIAL SETTING OF THE SLIPPER STEP 1.5 - 2 mm NOTE: The spur gear is NOT symetrical. The deeper side must be oriented to the inside Nylock nut M3 3x7x0.5 1.5x8...
  • Page 10 STEP M3X30 M3X10 M3X10 M3X10 M3X10 DIFF HEIGHT AND BELT TENSION SETTING: M3X8 Change the indicated inserts to move the diff up M3X12 STEP or down and to tighten / loosen the front belt tension. Inner part of right insert is shown M3X12 below pictures.

  • Page 11: Rear Assembly

    REAR ASSEMBLY STEP 2x10 2x10 M2x5 Rear uprights are NOT SYMMETRICAL. Use the upright with R on the left side, 10x15x4 and upright marked with L on the right side. 5x13x4 C-HUBS INSERTS Default setup STEP 3x33 M2.3x4 Roll center inserts STEP Default setup ASSEmBLY ORDER:...

  • Page 12: Step

    M3X16 STEP M3X16 M3X6 28.1 STEP 27.9 mm NOTE: 28.2 make sure to assemble the ballstud 15.25 mm through the conical shim in the direction indicated by the red arrow. 17.25 mm 17.25 mm 3x6x1 15.25 mm Page...

  • Page 13: Step

    NOTE: Do not tighten the m3x3 set screws yet. 29.1 They have to be tighten once the anti-roll bar is STEP assembled and centered. M3x3 29.2 4X7X3 Flanged M3X3 M3X3 NOTE: Do not overtighten the m3x3 set screws to avoid stripping the plastic rods ends STEP M3X25 M3X12...

  • Page 14: Front Assembly

    FRONT ASSEMBLY STEP M3X10 M3X10 M3X8 M3X8 M3X6 STEP 5x8x2.5 M3X6 5x8x2.5 5x8x2.5 5x8x2.5 STEP M3X10 M3X10 Steering crossbar assembly detail view 3x6x0.5 Page...

  • Page 15: Step

    STEP INCLUDED Note: Use spacers between the servo and the spline to ensure a min gap of M3X12 Flanged 0.5mm as shown 0.5 mm STEP NOTE: Select the correct servo lever for your servo brand. NOTE: make sure to put servo in neutral before mounting...

  • Page 16: Step

    38.1 STEP NOTE There are three types of steering arms. mORE LESS ACKERmAN ACKERmAN Default setup M3x10 38.2 2x10 M2x5 2x10 10x15x4 5x13x4 STEP M3x12 Steeringblock assembly detail view M3x12 Page...
  • Page 17 C-HUBS INSERTS STEP Default setup 3x27.5 M2.3x4 Roll center inserts STEP Default setup M3x12 STEP M3x6 Page...
  • Page 18 STEP M3x20 M3x20 M3x10 M3x12 Front Shocks and Camber Links default position detail view 44.1 STEP 26 mm 44.2 NOTE: make sure to assemble the ballstud through the conical shim in the direction indicated by the red arrow. 15.25 mm 17.25 mm 17.25 mm 15.25 mm...
  • Page 19 45.1 28 mm STEP 45.2 Note the orientation of the outer rod end. 15.25 mm 15.25 mm NOTE: 15.25 mm make sure to assemble the ballstud through the conical shim in the direction indicated by the red arrow. SHOCK ABSORBERS ASSEMBLY STEP 46.1 46.2...
  • Page 20 46.4 46.4 FRONT SHOCKS REAR SHOCKS Use some Use some silicone silicone oil during oil during assembly assembly 1.25 mm 1.25 mm 0.75 mm 0.75 mm 20.5mm 28.5mm 46.5 46.6 Apply the gasket and cap Fill shockbody and close fully. with silicone oil fully.
  • Page 21 NOTE: Do not overtighten and STEP use / smash bushing with the nut and note orientation of the lower shock pivot ball M3 Plastic Nut Flanged M3 Plastic Nut M3x16 Flanged Flanged M3x16 Flanged NOTE: Do not overtighten/ STEP smash the bushing with the nut and note location of the lower shock pivot ball.
  • Page 22 ELECTRONICS ASSEMBLY Tip: Use double sided NOT INCLUDED tape to mount the ESC STEP and Rx to the chassis. Note: make sure that 7mm m3x12 screw outside the spline. M3x12 7 mm M3x12 M3x12 STEP INCLUDED INCLUDED Page...

  • Page 23: Final Assembly

    Same for the body mounting holes. Remove body protection film outside of the body. Apply provided Serpent and Spyder decals, and mount the body on the bodyposts, with the provided bodyclips. Nut M4 flanged Page...

  • Page 24: Table Of Contents

    REF GUIDE: EXPLODED VIEWS and PARTS-LIST Contents FRONT & REAR GEAR-DIFF EXPLODED VIEW SHOCKS EXPLODED VIEW MID TRANSMISSION EXPLODED VIEW TRANSMISSION EXPLODED VIEW REAR ASSEMBLY EXPLODED VIEW FRONT ASSEMBLY EXPLODED VIEW FINAL ASSEMBLY I EXPLODED VIEW FINAL ASSEMBLY II EXPLODED VIEW OPTIONALS AND MERCHANDISING Page...

  • Page 25: Front & Rear Gear-Diff Exploded View

    FRONT & REAR GEAR-DIFF EXPLODED VIEW 500246 500247 REAR GEARDIFF 500246 110220 500253 110188 500248 500249 500290 500249 500257 500253 500290 500246 500248 500448 FRONT GEARDIFF 110220 500481 SHOCKS EXPLODED VIEW 500176 500184 110153 500179 500183 500183 500174 Front 500175 Rear 500178 500487 500177...

  • Page 26: Mid Transmission Exploded View

    MID TRANSMISSION EXPLODED VIEW Page...

  • Page 27: Transmission Exploded View

    TRANSMISSION EXPLODED VIEW Page...

  • Page 28: Rear Assembly Exploded View

    REAR ASSEMBLY EXPLODED VIEW Page...

  • Page 29: Front Assembly Exploded View

    FRONT ASSEMBLY EXPLODED VIEW Page...

  • Page 30: Final Assembly I Exploded View

    FINAL ASSEMBLY I EXPLODED VIEW Page...

  • Page 31: Final Assembly Ii Exploded View

    FINAL ASSEMBLY II EXPLODED VIEW Page...

  • Page 32: Optionals And Merchandising

    OPTIONALS AND MERCHANDISING Part no Description REAR SECTION 500010 Serpent Spyder Buggy SRX-4 4wd 1/10 500106 1/10 buggy rim rr yellow (2) 500205 Antiroll bar rr 1.1 SRX2 DECALS 500206 Antiroll bar rr 1.3 SRX2 1886 Decal Serpent black/white 1/10 (2) 500207 Antiroll bar rr 1.5 SRX2...
  • Page 33 190501 Tool-bag 190206 Hoody sweater Serpent black-zip (3XL) 190502 Pit-bag medium. 3 drawers 190207 Hoody sweater Serpent black-zip (4XL) ) 190504 Ballcup tool 190506 Toolset for onroad (17pcs) with tools bag 190507 Toolset for ep (16pcs) with tools bag 190508...
  • Page 34 - info@serpent.com Page...

Table of Contents