Jenn-Air JS48PPDBDA Design Manual page 17

I N S TA L L AT I O N G U I D E – F R A M E D M O D E L PA N E L S
BACKER PANEL
(A) Grille Panel
W Width
H Height
(B) Freezer Dispenser Panel
W Width
W1 Width
W2 Width
H Height
H1 Height
H2 Height
(C) Freezer Non-Dispenser Panel
W Width
H Height
(D) Refrigerator Panel
W Width
H Height
SPACER PANEL
(A) Grille Panel
W Width
H Height
(B) Freezer Dispenser Panel
W Width
W1 Width
W2 Width
H Height
H1 Height
H2 Height
(C) Freezer Non-Dispenser Panel
W Width
H Height
(D) Refrigerator Panel
W Width
H Height
FRONT DECORATOR PANEL
(A) Grille Panel
W Width
H Height
(B) Freezer Dispenser Panel
W Width
W1 Width
W2 Width
H Height
H1 Height
H2 Height
(C) Freezer Non-Dispenser Panel
W Width
H Height
(D) Refrigerator Panel
W Width
H Height
42" Wide Cabinet
in cm
40 1/4 102.24
8 3/4 22.23
15 1/16 38.26
2 5.08
14 1/2 36.83
69 1/8 175.58
34 1/16 86.52
48 1/8 122.24
15 1/16 38.26
69 1/8 175.58
22 5/16 56.67
69 1/8 175.58
in cm
39 1/4 99.7
7 3/4 19.69
14 1/16 35.72
2 5.08
14 1/2 36.83
68 1/8 173.04
34 1/16 86.52
48 1/8 122.24
14 1/16 35.98
68 1/8 173.04
21 5/16 54.13
68 1/8 173.04
in cm
40 1/4 102.24
8 3/4 22.23
14 7/8 37.78
2 1/4 5.72
14 1/4 36.20
69 1/4 175.90
34 5/16 87.15
47 13/16 121.44
14 7/8 37.78
69 1/4 175.90
22 1/8 56.20
69 1/4 175.90
48" Wide Cabinet
in cm
46 1/4 117.48
8 3/4 22.23
17 5/16 43.97
2 5.08
14 1/2 36.83
69 1/8 175.58
34 1/16 86.52
48 1/8 122.24
17 5/16 43.97
69 1/8 175.58
26 1/16 66.20
69 1/8 175.58
in cm
45 1/4 114.94
7 3/4 19.69
16 5/16 41.43
2 5.08
14 1/2 36.83
68 1/8 173.04
34 1/16 86.52
48 1/8 122.24
16 5/16 41.43
68 1/8 173.04
25 1/16 63.66
68 1/8 173.04
in cm
46 1/4 117.48
8 3/4 22.23
17 1/8 43.50
2 1/4 5.72
14 1/4 36.20
69 1/4 175.90
34 5/16 87.15
47 13/16 121.44
17 1/8 43.50
69 1/4 175.90
26 7/8 68.26
69 1/4 175.90
NOTES:
1. Use counter sink screws for attaching the
backer panel to the front panel.
2. On 42" custom panels, watch location of
handle mounting due to under cut of front
panel.
3. For freezer dispenser front panels, remove
fountain trim and tape to the backside of
the backer panel. Note: recycle symbol
should be visible and located at the
bottom.
4. You may want to remove any additional
material on the backer panel when used in
conjunction with a front panel. Remove
1/32" on thickness and 1/2" wide of
material on the inside surface of the backer
panel. This will help ease assembly of the
panel assembly onto the door.
Backer Panel Thickness 1/4" (0.64 cm)
Spacer Panel Thickness 0.100" (0.25 cm)
If Raised Panel is Used Overall Front Panel
Thickness Not to Exceed 1-1/4" (3.18 cm)
15