NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit horizonhobby. com and click on the support tab for this product. Meaning of Special Language The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product: NOTICE: Procedures, which if not properly followed, create a possibility of physical property...
Charging Warnings CAUTION: All instructions and • Always charge batteries away from fl ammable warnings must be followed exactly. materials. Mishandling of Li-Po batteries can result in a • Always inspect the battery before charging fi re, personal injury and/or property damage. •...
Transmitter Setup Table (BNF) DX6i SETUP LIST ADJUST LIST Model Type HELI TRAVEL ADJ D/R & Expo Swash Type 1 servo 90 Channel Travel Chan Sw Pos Expo THRO 100/100 REVERSE AILE AILE 100/100 Channel Direction ELEV 100/100 THRO ELEV RUDD 100/100 AILE...
Page 6
SYSTEM SETUP FUNCTION LIST Model Type HELI Servo Setup Swash Type Normal Chan Travel Reverse Chan Travel Reverse 100/100 Normal 100/100 Normal F-Mode Setup 100/100 Normal 100/100 Normal Switch 1 Switch B 100/100 Normal 100/100 Normal Hold Switch Switch H D/R &...
Transmitter Control (RTF) Flight mode Panic switch Recovery Bind Dual rate switch switch Power LED/fl ight mode indicator ON/OFF Switch When pressed down, trim buttons make a sound that increases or decreases in pitch at each pressing. The middle or neutral trim position is heard as a middle tone in the pitch range of the sounds.
If you purchased an RTF model, the transmitter is bound to the model at the factory. If for any reason you need to re-bind your Nano CPS to the MLP6DSM, follow the directions below: Binding Procedure for the MLP6DSM (RTF) 1.
Collective pitch up Collective pitch down Understanding the Primary Flight Controls If you are not familiar with the controls of your Nano CPS, take a few minutes to familiarize yourself with them before attempting your fi rst fl ight. Throttle...
fl ight control that always feels crisp and responsive. Flight Modes The Nano CPS RTF comes with the Blade • Both the cyclic and yaw controls are at fast, MLP6DSM aerobatic rate.
fl ight skills. which could cause the Nano CPS to descend rapidly. First Flight Preparation Flying Checklist ❏ Always turn the transmitter on fi rst •...
Tail boom is cracked Replace tail boom Poor tail authority The tail rotor blade is warped Twist rotor blade back into position or bent or replace Climb out rate is Main gear has slipped on the...
Page 13
Check main rotor blades and blade Helicopter vibrates or Damaged rotor blades, grips for cracks or chips. Replace shakes in fl ight spindle or blade grips damaged parts.
Spindle Tool Set BLH3323 Hardware Set EFLC1008 1s USB LiPo charger, 300mAh SPM6836 Replacement Servo Mechanics EFLRMLP6H MLP6DSM Heli SAFE transmitter Fast Flight Main Rotor Blade Set with BLH3311 Hardware BLH3021 Canopy Mounting Grommets (8) Optional Parts Part # Description BLH3318A...
Limited Warranty What this Warranty Covers have other rights which vary from state to state. Horizon reserves the right to change or modify this Horizon Hobby, LLC, (Horizon) warrants to the warranty at any time without notice. original purchaser that the product purchased (the “Product”) will be free from defects in materials WARRANTY SERVICES and workmanship at the date of purchase.
submitting the item for service you are agreeing to ATTENTION: Horizon service is limited to payment of the service without notification. Service Product compliant in the country of use estimates are available upon request. You must and ownership. If received, a non-compliant include this request with your item submitted for Product will not be serviced.
Need help?
Do you have a question about the Nano CPS and is the answer not in the manual?
Questions and answers