Table of Contents
Advertisement
2-6 Lower Frame Assembly
Installation
Secure the lower frame assembly P#(A1119) to the rear
frame of the mower using (4) 5/16"-18 x 1" HHCS
P#(K1154) and (4) 5/16"-18 nylon flange locknuts
P#(K2516). Then secure the lower frame assembly to
the PTO mount assembly P#(A1794) using (3) 5/16"-18
x 1" HHCS P#(K1154) and (3) 5/16"-18 nylon flange
locknuts P#(K2516) as shown in Figure 2-6.
Figure 2-6
Lower Frame
Assembly
(4) 5/16"-18 x 1" HHCS
(4) 5/16"-18 Nylon
Flange Locknut
2-7 Muffler Guard And Tow Hitch
Installation
Replace the tow hitch and muffler guard removed in step
2-1. Secure with (2) 5/16"-18 x 1" HHCS P#(K1154) and
(2) 5/16"-18 nylon flange locknuts P#(K2516) as shown
in Figure 2-7.
Figure 2-7
(2) 5/16"-18 x 1" HHCS
Tow Hitch
2-8 Upper Frame Assembly
Installation
Lift the upper frame assembly P#(A1114) into position,
and slide onto the lower frame assembly as shown in
Figure 2-9 and secure with (2) 1/2" x 2-1/4" clevis pins
P#(K0133) and (2) hair pin clips P#(K0088). Note: It is
recommended that someone assist you when installing
the upper frame assembly.
(3) 5/16"-18 x 1" HHCS
(3) 5/16"-18 Nylon
Flange Locknut
(2) 5/16"-18 Nylon
Flange Locknut
Muffler Guard
2-9 Top Assembly To Upper Frame
Assembly Installation
Position the top assembly P#(A1148) above the upper
frame assembly as shown in Figure 2-9. Fasten the top
assembly to the upper frame assembly using (2) 5/16"-
18 x 2-1/2" HHCS P#(K0125), (2) 1/4" Flat Washer
P#(K0037), and (2) 5/16"-18 nylon flange locknuts
P#(K2516). Leave the locknuts slightly loose, to allow
the top assembly to open and close easily. Refer to
Figure 2-9 for hardware location.
Figure 2-9
Top Assembly
2-10 Inlet Installation
Insert the Inlet P#(V0019) into the hole on the top
assembly from the inside and then snap the inlet into
place. The inlet should pivot freely about the hole.
2-11 Hinge Kit Assembly Installation
Assemble the hinge kit as shown in Figure 2-11, using
(2) 5/16"-18 x 1" HHCS P#(K1154), (3) 5/16"-18 nylon
flange locknuts P#(K2516), (5) 1/4" flat washers
P#(K0037) and (2) swing arm brackets P#(ZT-0004).
Place (1) vinyl cap P#(J0289) on the end of the hex bolts
as shown in Figure 2-11. Leave the nuts loose enough to
allow fluid movement of the top when opening and
closing. When opened, the top should rest on the middle
joint of the hinge allowing it to remain up.
Figure 2-11
K1154
K2516
J0289
8
Hex
Bolt
Washer
(2) 5/16"-18 x 2-1/2" HHCS
(2) 1/4" Flat Washer
(2) 5/16"-18 Nylon
Flange Locknut
K0037
ZT-0004
Nylon
Flange
Locknut
Flat
Advertisement
Table of Contents
