ICS 695GC Operator's Manual
  1. Manuals
  2. Brands
  3. ICS Manuals
  4. Chainsaw
  5. 695GC
  6. Operator's manual

ICS 695GC Operator's Manual

Hide thumbs Also See for 695GC:
Table of Contents

Advertisement

Quick Links

See also: Operator's Manual
695GC / 695F4
OPERATOR MANUAL
i
© 2015 ICS, Blount International Inc. Specifications are subject to change
without notice. REV
F/N 545067
010515

Advertisement

Table of Contents
loading

Related Manuals for ICS 695GC

Summary of Contents for ICS 695GC

  • Page 1 695GC / 695F4 OPERATOR MANUAL © 2015 ICS, Blount International Inc. Specifications are subject to change without notice. REV F/N 545067 010515...

  • Page 2: Table Of Contents

    This is a professional tool and is soley intended for use by trained and experienced operators. The 695GC / 695F4 chainsaw is designed to cut concrete, stone, and masonry when used with the appropriate genuine ICS Diamond Chain. Ductile iron pipe may be cut ONLY if using PowerGrit Utility Saw Chain.

  • Page 3: Symbols & Labels

    IMPORTANT A potential situation exists which, if not avoided, may result in product or property damage. © 2015 ICS, Blount International Inc. Specifications are subject to change without notice. REV F/N 545067 010515...
  • Page 4 Always use: • Protective helmet • Ear protection • Protective glasses or full face protection Wear hand protection © 2015 ICS, Blount International Inc. Specifications are subject to change without notice. REV010515 F/N 545067...

  • Page 5: Safety

    Utility Saw Chain). Segment loss or ® diamond chain breakage may occur. • See page 24 for information about cutting ductile iron pipe with PowerGrit chain. © 2015 ICS, Blount International Inc. Specifications are subject to change without notice. REV F/N 545067 010515...
  • Page 6 • Never start saw unless the bar, chain and side cover are properly installed. © 2015 ICS, Blount International Inc. Specifications are subject to change without notice. REV010515 F/N 545067...
  • Page 7 • To avoid electrocution, check for live electrical wiring near cutting area. ICS diamond chain saws require a continuous water supply to the guidebar and chain, a key purpose of which is dust suppression. The potential for airborne particulates depends on many factors including, but not limited to, the material being cut, application and cutting environment.
  • Page 8 THE FOLLOWING SYMBOL APPLIES TO ALL ITEMS LISTED ON THIS PAGE IMPORTANT Note: The concrete chain saw is equipped with a 2-stroke engine and must always be run using a mixture of gasoline and ICS 2-stroke ® engine oil, or other high quality 2-stroke oil that has been formulated for air cooled power equipment.

  • Page 9: Technical Specifications

    (rear handle) Engine Break-in Period One tank, without cutting, cycling throttle NGK BPMR7A or Champion RCJ6Y Electrode Spark Plug gap 0.020 in (0.5 mm) © 2015 ICS, Blount International Inc. Specifications are subject to change without notice. REV F/N 545067 010515...

  • Page 10: Setup

    GUIDEBAR AND DIAMOND CHAIN INSTALLATION STEP 1 Loosen side cover nut and remove side cover. STEP 2 Place bar onto stud and engage alignment block. © 2015 ICS, Blount International Inc. Specifications are subject to change without notice. REV010515 F/N 545067...
  • Page 11 Install the side cover and ensure chain adjustment pin engages hole in bar. Do not fully tighten side cover nut until after chain is properly tensioned. © 2015 ICS, Blount International Inc. Specifications are subject to change without notice. REV F/N 545067...
  • Page 12 CAUTION: Be aware that the guidebar rails may develop sharp edges over time so always pull the diamond chain by the diamond segments. © 2015 ICS, Blount International Inc. Specifications are subject to change without notice. REV010515 F/N 545067...
  • Page 13 When a chain stretches to a point where the drive links are hanging approximately 1/2 in (12 mm) to 3/4 in (18 mm) below the bar, it is time to tension the chain. © 2015 ICS, Blount International Inc. Specifications are subject to change without notice. REV F/N 545067...
  • Page 14 20-25 ft-lbs (27-33 Nm). STEP 8 Attach to water source with pressure of not less than 20 psi (1.5 bar). © 2015 ICS, Blount International Inc. Specifications are subject to change without notice. REV010515 F/N 545067...

  • Page 15: Operation

    • Always provide adequate ventilation when handling fuel. • Use caution when handling gasoline. Avoid direct contact with skin or inhaling fuel vapor. © 2015 ICS, Blount International Inc. Specifications are subject to change without notice. REV F/N 545067 010515...
  • Page 16 Slowly open the fuel cap to release any pressure that may have built-up in the tank. • After adding fuel, carefully install the fuel cap and tighten firmly by hand. © 2015 ICS, Blount International Inc. Specifications are subject to change without notice. REV010515 F/N 545067...
  • Page 17 6. Place foot on the base of the rear handle, and place one hand on front handle. Decompression Valve Stop Switch Choke Throttle Trigger Lever Trigger Interlock Primer Bulb © 2015 ICS, Blount International Inc. Specifications are subject to change without notice. REV F/N 545067 010515...
  • Page 18 STOPPING THE SAW • To turn the engine off, push stop switch to the "STOP" position. Close water valve. © 2015 ICS, Blount International Inc. Specifications are subject to change without notice. REV010515 F/N 545067...
  • Page 19 © 2015 ICS, Blount International Inc. Specifications are subject to change without notice. REV F/N 545067...
  • Page 20 = 12 in x 12 in x 12 in = 150 lbs (30 cm x 30 cm x 30 cm = 68 kg). • Check for and remove any obstructions (plumbing, electrical conduit, air ducts, etc,) that may interfere with the cut. © 2015 ICS, Blount International Inc. Specifications are subject to change without notice. REV010515 F/N 545067...
  • Page 21 Plunge cut instead of starting at the top surface of the wall. This will reduce chatter, extend diamond life, create a straighter cut and more quickly enable the use of the WallWalker. © 2015 ICS, Blount International Inc. Specifications are subject to change without notice. REV F/N 545067...
  • Page 22 When using a new chain, you can increase the initial cutting speed by “opening up the diamonds”. Make a few cuts in an abrasive material such as a cinder block. © 2015 ICS, Blount International Inc. Specifications are subject to change without notice. REV010515 F/N 545067...
  • Page 23 After cleaning the saw, spray the entire saw body, chain, bar, and drive sprocket with lightweight oil. Using lightweight oil on the saw will minimize rust and help reduce slurry build up. © 2015 ICS, Blount International Inc. Specifications are subject to change without notice. REV F/N 545067...

  • Page 24: Maintenance

    1. Change the spark plug. Adjust the electrode to 0.020 in (0.5 mm). 2. Check the fuel filter located inside the fuel tank. Clean or replace if clogged. © 2015 ICS, Blount International Inc. Specifications are subject to change without notice. REV010515 F/N 545067...

  • Page 25: Air Filter

    • When replacing the air filter, clean the area inside the air intake housing with a clean rag prior to installing new filter. © 2015 ICS, Blount International Inc. Specifications are subject to change without notice. REV F/N 545067 010515...
  • Page 26 Oil the starter pawls by spraying lightweight oil into the starter housing through the vents. • Check the starter cord for fraying, replace if necessary. © 2015 ICS, Blount International Inc. Specifications are subject to change without notice. REV010515 F/N 545067...
  • Page 27 Tighten the knot firmly and ensure that free end of rope is as short as possible. Secure the other end of the rope in the starter handle. © 2015 ICS, Blount International Inc. Specifications are subject to change without notice. REV F/N 545067...
  • Page 28 Slowly release the starter cord to enable the pulley to fit between the pawls. • Insert and tighten the screws. Use blue Loctite #242. ® © 2015 ICS, Blount International Inc. Specifications are subject to change without notice. REV010515 F/N 545067...
  • Page 29 20-25 ft-lbs (27-33 Nm). • Chain tensioning is attempted without Chain Tensioner loosening the side cover nut. • Concrete debris in tensioner pocket. © 2015 ICS, Blount International Inc. Specifications are subject to change without notice. REV F/N 545067 010515...
  • Page 30 CAUTION: Wear safety glasses. • Remove the half collars and retaining washer from the shaft. • Slide the drive sprocket off of the splined adapter. © 2015 ICS, Blount International Inc. Specifications are subject to change without notice. REV010515 F/N 545067...
  • Page 31 • Check proper spring clip engagement by carefully prying out on the half collars. Both half collars should be firmly secured to the shaft. © 2015 ICS, Blount International Inc. Specifications are subject to change without notice. REV F/N 545067...
  • Page 32 Carburetor idle screw decrease in power and drop in RPM at full throttle, the filter may have become dirty or saturated with water. © 2015 ICS, Blount International Inc. Specifications are subject to change without notice. REV010515 F/N 545067...
  • Page 33 • The bar is solely a guide track for the chain. Never use the bar to lift, twist or pry concrete material. © 2015 ICS, Blount International Inc. Specifications are subject to change without notice. REV F/N 545067 010515...

  • Page 34: Troubleshooting

    Inserting saw into slot narrower than diamond chain DIAMOND CHAIN BREAKAGE segments Not enough feed pressure while cutting. Avoid letting the saw bounce and chatter. © 2015 ICS, Blount International Inc. Specifications are subject to change without notice. REV010515 F/N 545067...

  • Page 35: Reference

    3 + 7 + 3 + 7 = 20 feet 3. Multiply the two numbers 8 in x 20 ft = 160 in-ft © 2015 ICS, Blount International Inc. Specifications are subject to change without notice. REV F/N 545067 010515...

  • Page 36: Emission Control Warranty Statement

    The emission control system on 2009 and later small non-road engines is warranted for two years. If any emission related part on your engine (as listed above) is defective, the part will be repaired or replaced by ICS. © 2015 ICS, Blount International Inc. Specifications are subject to change...
  • Page 37 Operator′s Manual. ICS recommends that you retain all receipts covering maintenance on your small non-road engine, but ICS cannot deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance.

  • Page 38: Declaration Of Conformity

    Portable, hand-held, internal combustion cutting-off machines - safety EN 1454:1997 CLARIFICATION OF PRODUCT CLASS: The ICS 695GC/695F4 Gas Saw, using the appropriate genuine ICS Diamond Chain, is designed to ONLY cut concrete or designated materials other than wood. The cutting means is by grinding through the work-piece, using a continuous water supply as a coolant and lubricant.

  • Page 39: Service Centers

    101 WEST TERRA COTTA CRYSTAL LAKE ROCK-CRETE EQUIPMENT LTD. 604.464.1448 50 BURBIDGE STREET COQUITLAM POWER TOOL KLINIC LTD. 403.276.4633 #11 2219 - 35th AVENUE NE CALGARY © 2015 ICS, Blount International Inc. Specifications are subject to change without notice. REV F/N 545067 010515...

  • Page 40: Without Notice. Rev010515 F/N

    695GC / 695F4 OPERATOR MANUAL ICS, Blount Inc. 4909 SE International Way Portland, OR 97222 Tel 800-321-1240 Fax 503-653-4393 icsbestway.com © 2015 ICS, Blount International Inc. Specifications are subject to change without notice. REV010515 F/N 545067...

This manual is also suitable for:

695f4

Table of Contents