ICS 695GC Operator's Manual
  1. Manuals
  2. Brands
  3. ICS Manuals
  4. Chainsaw
  5. 695GC
  6. Operator's manual

ICS 695GC Operator's Manual

Chain saw
Hide thumbs Also See for 695GC:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Operator's Manual
695GC / 695F4
OPERATOR'S MANUAL
© 2010 ICS, Blount International Inc. Specifications are subject to change without notice. REV0910 F/N 545067

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 695GC and is the answer not in the manual?

Questions and answers

Related Manuals for ICS 695GC

Summary of Contents for ICS 695GC

  • Page 1 695GC / 695F4 OPERATOR’S MANUAL © 2010 ICS, Blount International Inc. Specifications are subject to change without notice. REV0910 F/N 545067...

  • Page 3: Table Of Contents

    This is a professional tool and is soley intended for use by trained and experienced operators. The 695GC / 695F4 chainsaw is designed to cut concrete, stone, and masonry when used with the appropriate genuine ICS Diamond Chain. Ductile iron pipe may be cut ONLY if using PowerGrit Utility Saw Chain.

  • Page 4: Symbols & Labels

    Always use: • Protective helmet • Ear protection • Protective glasses or full face protection Wear hand protection © 2010 ICS, Blount International Inc. Specifications are subject to change without notice. REV0910 F/N 545067...

  • Page 5: Safety

    Utility Saw Chain). Segment loss or diamond chain breakage may occur. • See page 16 for information about cutting ductile iron pipe with PowerGrit chain. © 2010 ICS, Blount International Inc. Specifications are subject to change without notice. REV0910 F/N 545067...
  • Page 6 Provide adequate ventilation when working in an enclosed area. Breathing exhaust gases is dangerous. • To avoid electrocution, check for live electrical wiring near cutting area. © 2010 ICS, Blount International Inc. Specifications are subject to change without notice. REV0910 F/N 545067...
  • Page 7 To break-in the engine, run one full tank of 25:1 (4%) fuel at idle, cycling the throttle every 5 to 10 minutes to prevent loading. • Failure to break-in an engine may result in piston seizure. © 2010 ICS, Blount International Inc. Specifications are subject to change without notice. REV0910 F/N 545067...

  • Page 8: Technical Specifications

    (rear handle) Engine Break-in Period One tank, without cutting, cycling throttle NGK BPMR7A or Champion RCJ6Y Spark Plug Electrode gap 0.020 in (0.5 mm) © 2010 ICS, Blount International Inc. Specifications are subject to change without notice. REV0910 F/N 545067...

  • Page 9: Set-Up

    Install the side cover and ensure chain adjustment pin engages hole in bar. Do not fully tighten side cover nut until after chain is properly tensioned. © 2010 ICS, Blount International Inc. Specifications are subject to change without notice. REV0910 F/N 545067...
  • Page 10 1/2 in (12 mm) to 3/4 in (18 mm) below the bar, it is time to tension the chain. © 2010 ICS, Blount International Inc. Specifications are subject to change without notice. REV0910 F/N 545067...
  • Page 11 20-25 ft-lbs (27-33 Nm). STEP 8 Attach to water source with pressure of not less than 20 psi (1.5 bar). © 2010 ICS, Blount International Inc. Specifications are subject to change without notice. REV0910 F/N 545067...

  • Page 12: Operation

    Slowly open the fuel cap to release any pressure that may have built-up in the tank. • After adding fuel, tighten the fuel cap carefully and secure with a wrench. © 2010 ICS, Blount International Inc. Specifications are subject to change without notice. REV0910 F/N 545067...
  • Page 13 Note: To hold the trigger fully open it may be necessary to insert right foot into rear handle opening and twist. STOPPING THE SAW • To turn the engine off, push stop switch to the "STOP" position. Close water valve. © 2010 ICS, Blount International Inc. Specifications are subject to change without notice. REV0910 F/N 545067...
  • Page 14 = 12 in x 12 in x 12 in = 150 lbs (30 cm x 30 cm x 30 cm = 68 kg). • Check for and remove any obstructions (plumbing, electrical conduit, air ducts, etc,) that may interfere with the cut. © 2010 ICS, Blount International Inc. Specifications are subject to change without notice. REV0910 F/N 545067...
  • Page 15 When using a new chain, you can increase the initial cutting speed by “opening up the diamonds”. Make a few cuts in an abrasive material such as a cinder block. © 2010 ICS, Blount International Inc. Specifications are subject to change without notice. REV0910 F/N 545067...
  • Page 16 After cleaning the saw, spray the entire saw body, chain, bar, and drive sprocket with lightweight oil. Using lightweight oil on the saw will minimize rust and help reduce slurry build up. © 2010 ICS, Blount International Inc. Specifications are subject to change without notice. REV0910 F/N 545067...

  • Page 17: Maintenance

    1. Change the spark plug. Adjust the electrode to 0.020 in (0.5 mm). 2. Check the fuel filter located inside the fuel tank. Clean or replace if clogged. © 2010 ICS, Blount International Inc. Specifications are subject to change without notice. REV0910 F/N 545067...
  • Page 18 Oil the starter pawls by spraying lightweight oil into the starter housing through the vents. • Check the starter cord for fraying, replace if necessary. © 2010 ICS, Blount International Inc. Specifications are subject to change without notice. REV0910 F/N 545067...
  • Page 19 CAUTION: Check that the pulley can be turned an additional 1/2 turn when the starter cord is pulled all the way out. © 2010 ICS, Blount International Inc. Specifications are subject to change without notice. REV0910 F/N 545067...
  • Page 20 20-25 ft-lbs (27-33 Nm). • Chain tensioning is attempted without loosening the side cover nut. • Concrete debris in tensioner pocket. Chain Tensioner © 2010 ICS, Blount International Inc. Specifications are subject to change without notice. REV0910 F/N 545067...
  • Page 21 CAUTION: Wear safety glasses. • Remove the half collars and retaining washer from the shaft. • Slide the drive sprocket off of the splined adapter. © 2010 ICS, Blount International Inc. Specifications are subject to change without notice. REV0910 F/N 545067...
  • Page 22 • Always use the recommended spark plug type. Using the wrong spark plug can severely damage the piston and cylinder (NGK #BPMR7A). © 2010 ICS, Blount International Inc. Specifications are subject to change without notice. REV0910 F/N 545067...
  • Page 23 Periodically clean the water ports inside the groove of the bar using a small diameter piece of wire. • The bar is solely a guide track for the chain. Never use the bar to lift, twist or pry concrete material. © 2010 ICS, Blount International Inc. Specifications are subject to change without notice. REV0910 F/N 545067...

  • Page 24: Troubleshooting

    Not enough feed pressure while cutting. Avoid letting the saw bounce and chatter. Further questions? Call +32 10 301 251 or visit our website at icsbestway.com © 2010 ICS, Blount International Inc. Specifications are subject to change without notice. REV0910 F/N 545067...

  • Page 25: Reference

    2. Determine the length of the cut in feet. 3 + 7 + 3 + 7 = 20 feet 3. Multiply the two numbers 8 in x 20 ft = 160 in-ft © 2010 ICS, Blount International Inc. Specifications are subject to change without notice. REV0910 F/N 545067...
  • Page 26 695GC / 695F4 OPERATOR'S MANUAL ICS, Blount Europe S.A. rue Emile Francqui 5 1435 Mont-Saint-Guibert, Belgium Tel +32 10 301 251 Fax +32 10 301 259 icsbestway.com © 2010 ICS, Blount International Inc. Specifications are subject to change without notice. REV0910 F/N 545067...

This manual is also suitable for:

695f4

Table of Contents