Comfort Flame Rochester STDMN Installation And Operation Instructions Manual

M see-through and peninsula direct-vent gas fireplaces

Advertisement

Quick Links

WELCOME HOME TO WARMTH
P/N 900476-00 Rev. NC 08/2015
Ce manuel est disponible en francais, simplement
en faire la demande. Numéro de la pièce 900476-01.
P900476-00
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future
reference.
This appliance may be installed in an aftermarket permanently located, manufactured home (USA only)
or mobile home, where not prohibited by local codes. This appliance is only for use with the type of gas
indicated on the rating plate. This appliance is not convertible for use with other gases, unless a certified kit
is used.
Cet appareil peut installé dans une maison préfabriquée (mobile) déjà installée à demeure, si les réglements
locaux le permettent. Ce appareil doit être utilisé uniquement avec le type de gaz indiqué sure la plaque
signalétique. Cet appareil ne peut être converti à d'autres gaz, sauf si une trousse de conversion est utilsée.
WARNING:
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could
result in serious injury, death, or property damage.
- Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
- WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use
any phone in your building.
• Leave the building immediately.
• Immediately call your gas supplier from a neigh-
bor's phone. Follow the gas supplier's instruc-
tions.
• If you cannot reach your gas supplier, call the
fire department.
- Installation and service must be performed by
a qualified installer, service agency or the gas
supplier.
Installation and Operation Instructions
TM
Rochester
Gas Fireplaces
Models
PFS
®
C
US
Report No. F14-165
Installateur : Laissez cette notice avec l'appareil.
Consommateur : Conservez cette notice pour
consultation ultérieure.
See-Through and Peninsula Direct-Vent
TM
RochesterSTDMN
RochesterSTDMP
AVERTISSEMENT:
RISQUED'INDENDIE OU D'EXPLOSION
Le non-respect Des avertissements de sécurité
pourrait d'entraîner des blessures graves, la mort
ou des dommages matériels.
- Ne pas entreposer ni utilizer d'essence ni d'autres
vapeurs ou liquides inflammables dans le voisinage
de cet appareil ou de tout autre appareil.
- QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ:
• Ne pas tenter d'allumer d'appareil.
• Ne touchez à aucan interrupteur. Ne pas vous servir
des téléphones se trouvant dans le bâtiment où
vous trouvez.
• Sortez immédiatement de bâtiment.
• Appelez immédiatement votre fournisseur de
gaz depuis un voisin. Suivez les instructions du
fournisseur.
• Si vous ne pouvez rejoindre le fournisseur de gaz,
appelez le service des incindies.
- L'installation et l'entretien doivent être assurés par
un installateur ou un service d'entretien qualifié
ou par le fournisseur de gaz.
RochesterPFDMN
RochesterPFDMP

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Rochester STDMN and is the answer not in the manual?

Questions and answers

Summary of Contents for Comfort Flame Rochester STDMN

  • Page 1 Installation and Operation Instructions Rochester See-Through and Peninsula Direct-Vent WELCOME HOME TO WARMTH Gas Fireplaces P/N 900476-00 Rev. NC 08/2015 Models Ce manuel est disponible en francais, simplement ® en faire la demande. Numéro de la pièce 900476-01. RochesterPFDMN RochesterSTDMN RochesterPFDMP RochesterSTDMP Report No.
  • Page 2 Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 SAFETY AND YOUR FIREPLACE See attached color flyer for proper color representation DANGER HOT GLASS WILL CAUSE BURNS. DO NOT TOUCH GLASS UNTIL COOLED.
  • Page 3 Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 La sécurité et Safety and Your Seguridad y su votre foyer Fireplace chimenea All parts of your ¡Todas las partes de la Toutes les parties de votre IHP fireplace get chimenea IHP se ponen...
  • Page 4: Table Of Contents

    Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 TABLE OF CONTENTS PACKAGING GENERAL INFORMATION Packaging .........Page 4 The assembled vented gas fireplace heater is WARNING Introduction ........Page 4 packaged with: General Information ......Page 4 1 - the logs are packaged in a carton located Young children should be care-...
  • Page 5 Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 The appliance, when installed, must be electri- NOTE: Installation and repair should be done WARNING by a qualified service person. The appliance cally grounded and wired in accordance with should be inspected before use and at least local codes or, in the absence of local codes,...
  • Page 6: Commonwealth Of Massachusetts

    Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 Gas Pressure - All Models COMMONWEALTH OF MASSACHUSETTS Orifice Sizes - Sea Level to High Altitude REQUIREMENTS (All Models) Tables 2 and 3 show the appliances' inlet and manifold gas pressure requirements: These appliances are tested and approved for These appliances are approved for installation in...
  • Page 7: Cold Climate Insulation

    Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 COLD CLIMATE INSULATION For cold climate installations, seal all cracks around your appliance with noncombustible material and wherever cold air could enter the room.
  • Page 8: Vent Termination Clearances

    Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 Be aware that this is a heat producing ap- Vertical Vent Termination Clearances pliance. Objects placed above the unit are Termination Heights For Vents exposed to elevated temperatures.
  • Page 9 Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 EXTERIOR HORIZONTAL VENT TERMINATION CLEARANCE REQUIREMENTS Inside Corner Outside Corner Recessed Location See Figure 5 Fixed Balcony with No Side Wall Balcony with Perpendicular Side Wall Openable Fixed Closed Closed...
  • Page 10: Appliance And Vent Clearances

    Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 MINIMUM CLEARANCES TO COMBUSTIBLES Hearth Extension - A hearth extension is not required with this appliance. If a hearth exten- Appliance And Vent Clearances sion is used, do not block the lower control compartment door.
  • Page 11: Detailed Installation Steps

    Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 WARNING MINIMUM CLEARANCES Inches (millimeters) Sides 1/2 in. (13) Failure to position the parts in accordance with these 0 (0) from Spacers Or Dimples ** diagrams or failure to use only parts specifically Top of Appliance 5 (127)
  • Page 12: Typical Installation Sequence

    Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 Step 1. FRAMING Step 4. (Page 16) Install the vent system and exterior termination. Pressure Relief Plates Frame these appliances as illustrated in Figures Step 5.
  • Page 13 Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 RochesterST SPECIFICATIONS Natural Gas BTU Input 30,000 Propane Gas BTU Input 28,000 ***This dimension does not include the addition 4-1/2" Inner / Co-axial DV Vent Size of drywall to the inside of **20-3/4...
  • Page 14 Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 RochesterPF SPECIFICATIONS Fireplace Framing Specifications Notes: • Inches (millimeters) • Minimum Framing Stud Size is 2 x 4 Natural Gas BTU Input 30,000 •...
  • Page 15: Step 2. Routing Gas Line

    Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 Step 2. ROUTING GAS LINE IMPORTANT: If propane is used, be aware that Schedule 40 if tank size is too small (i.e. under 100-lbs, if Black Iron Pipe Route a 1/2"...
  • Page 16: Step 4. Install The Venting System

    Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 Step 4. INSTALL THE VENT SYSTEM CROSS SECTION Securing Screws Top Vent Vent Seal Cap General Information (OUTSIDE of Appli ance) These instructions should be used as a guideline and do not supersede Insulation local codes in any way.
  • Page 17: Vertical Termination Systems

    Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 VERTICAL TERMINATION SYSTEMS (ROOF) i t c i t c See Figure 19 and Figures 29-33 on i t c Pages 20-21 a n d t h e i r a s s o c i a t e d i t c Vertical Vent Tables which illustrate the various vertical venting configurations that are possible...
  • Page 18 Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 Vertical (Offset) Installation B. Attach vent components to appliance - C. Attach vent components to each other - Other vent sections may be added to the previously Secure Vent SV4.5 Direct-Vent system compo- ®...
  • Page 19 Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 F. Change vent direction to horizontal/inclined H. Frame roof opening - Identify location for run - At transition from or to a horizontal/in- vent at the roof.
  • Page 20: Vertical Vent Tables And Figures

    Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 VERTICAL VENT FIGURES/TABLES Table A NOTE: Secure Vent (rigid vent pipe) is shown ® in the figures; Secure Flex (flexible vent pipe) V Minimum ®...
  • Page 21 Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 VERTICAL VENT FIGURES / TAbLES (CONTINUED) Table C Maximum H Maximum V Minimum feet (meter) feet (meter) feet (meter) Ceiling Firestop / (1.524) (0.610) (0.305)
  • Page 22: Horizontal Termination System

    Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 HORIZONTAL (OUTSIDE WALL) Support TERMINATION SYSTEM Horizontal / Inclined Run Building Brackets Support Figures 34, and Figures 37 to 42 on Page Framing SV4.5HT-2 Termination...
  • Page 23 Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 J. Assemble vent run to exterior wall - If not To help minimize water infiltration it Typical previously measured, locate the center of the is recommended that the Firestop/ Termination Spacer (SV4.5HF) be installed on...
  • Page 24: Horizontal Vent Tables And Figures

    Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 HORIZONTAL VENT FIGURES/TABLES Table F NOTE: Secure Vent components (rigid vent pipe and terminal) are ® shown in the figures; Secure Flex components (flexible vent pipe and ®...
  • Page 25 Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 HORIZONTAL VENT FIGURES/TAbLES (continued) Table G V Minimum Maximum H Maximum feet (meter) feet (meter) feet (meter) (1.524) (0.610) (0.305) (3.048) (1.219) (0.610) (4.572) (1.829)
  • Page 26 Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 HORIZONTAL VENT FIGURES/TAbLES (continued) When using Secure Flex , use ® Example: If 20 feet total (H+H Wall Firestop / Spacer Firestop / Spacer SF4.5VF horizontal vent run is needed, then 4 (SV4.5HF) When using Secure Flex, use...
  • Page 27: Venting Using Flexible Vent Pipe

    Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 VERTICAL OR HORIZONTAL VENTING USING SECuRE FlEx ® KITS AND COMPONENTS FLEX VENT NOTE: OUTER PIPE IS PULLED AWAY TO Secure Flex venting kits and components may SHOW THE DETAIL OF THE INNER PIPE ®...
  • Page 28: Step 5. Field Wiring

    Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 Step 5. FIELD WIRING Refer to Millivolt Wiring for millivolt appliances. CAUTION The gas valve is set in place and pre-wired at the factory.
  • Page 29: Step 6. Optional Blower Kit Wiring

    Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 Step 7. CONNECTING GAS LINE Step 6. WIRING - OPTIONAL FORCED AIR CAUTION BLOWER KIT Make gas line connections.All codes require a Remove the carton support from shut-off valve mounted in the supply line.
  • Page 30: Step 8. Verifying Appliance Operation

    Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 TEST ALL CONNECTIONS FOR GAS LEAKS NOTE: lighting Instructions are also found on B. Brush all joints and connections with the gas (FACTORY AND FIELD): the literature tag tied to the gas piping next leak test solution to check for leaks.
  • Page 31 Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 The flame should project 1" (25 mm) beyond the hood at all three ports (see Figure 52). Replace logs if removed for pilot inspection. To light the burner;...
  • Page 32: Step 9. Installing Logs

    Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 Step 9. INSTALL VERMICULITE, GLOWING EMbERS AND LOGS NOTE: Turn off all electricity to the appliance before you install vermiculite, embers and logs. DO NOT attempt to install the logs until the appliance installation has been completed, the gas line connected and tested for leaks and the initial burner operation has been checked out.
  • Page 33 Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 INSTALLATION STEPS: 7. Place Log (B) as shown in Figure 57. READ WARNINGS ON PAGE 34 BEFORE PROCEEDING Position Log (b) Against The back Of The Grate Here 1.
  • Page 34 Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 10. Place Log (E) as shown in Figure 60. WARNING Position The Round End Of Log (E) Against The Notch Of • DO NOT attempt to install the logs until the Log (D) Here.
  • Page 35: Step 10. Remove/Install Glass Door

    Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 Step 10. REMOVING AND INSTALLING Step 11. BURNER ADJUSTMENTS Locate the two (2) glass door spring latches at the top of the control compartment (see Figure THE GLASS DOOR Flame Appearance and sooting 62).
  • Page 36 Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 WARNINGS • Air shutter adjustment should only be performed by a quali- fied professional service tech- nician. • Ensure front glass panel are in place and sealed during adjustment.
  • Page 37: Step 12. Hood Installation

    Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 Decrease Shutter Opening In This Direction Combustible Wall This Area Must Remain Framing 3" (76 mm) Clear of Combustible Materials Combustible Finished Wall Orifice Materials 1 in.
  • Page 38: Step 13. Attaching Safety-In-Operation Warnings

    Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 STEP 13. ATTACHING SAFETY-IN-OPERATION WARNINGS It is the installers responsibility to ensure these warnings are properly affixed during installation. These warning labels are a critical step in informing consumers of safe operation of this appliance.
  • Page 39: Installation Accessories

    Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 INSTALLATION ACCESSORIES Listed Secure Vent Components ® Cat. No. Model Description Cat. No. Model Description 77L70 SV4.5L6 6 Inch (152 mm) Vent Sections (Rigid) 77L71 SV4.5L12...
  • Page 40 Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 INSTALLATION ACCESSORIES (CONTINUED) Listed Secure Vent Components ® Listed Secure Flex Components ® Cat. # Model Description Cat. # Model Description These termination kits include firestop/spacer, gear clamps and flex adaptor. 17M52 SV4.5HGS-1 Te r m i n a t i o n G u a r d ,...
  • Page 41: Gas Conversion Kits

    Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 GAS CONVERSION KITS Natural Gas to Propane Gas Conversion Kits WARNING Fireplace Cat. No. Model No. (model) This conversion kit shall be installed by a qualified service agency in ST/PF-DMN H3360 accordance with the manufacturer’s instructions and all applicable codes...
  • Page 42 Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 Step 5. Attach manometer to the manifold side pressure test fitting and verify manifold pres- Air Shutter Pan Burner sure reads 3.5 inches water column (0.87 kPa) Adjustment Lever for natural gas, and 10.0 inches water column (2.49 kPa) for propane gas.
  • Page 43 Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 b. Install the burner as shown in Figure 72. Step 8. Reassemble the remaining components by reversing the procedures outlined in the Ensure that the arm of the venturi of the burner preceding steps.
  • Page 44: Operation/Care Of Your Appliance

    Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 OPERATION AVERTISSEMENT Les enfants et les adultes CONGRATULATIONS! devraient être infor-més des dangers que posent les tempéra- In selecting this Innovative Hearth Products tures de surface élevées et se direct-vent gas appliance you have chosen tenir à...
  • Page 45 Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 NOTE: Installation and repair should be Due to high temperatures the appliance WARNING should be located out of traffic and away done by a qualified service person. The from furniture and draperies.
  • Page 46 Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 BTU Input Deration - At higher elevations, the amount Manifold Gas Supply Pressure of BTU fuel value delivered must be reduced (all models) by either using gas that has been derated by These fireplaces are designed as supplemental Fuel #...
  • Page 47: Gas Controls Access

    Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 OPERATION AND CARE OF YOUR APPLIANCE WARNING Young children should be carefully supervised when they are in the same room as the appliance. Toddlers, young children and others may be susceptible to accidental contact burns.
  • Page 48: Variable Flame Adjustment

    Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 Variable Flame Height Adjustment Variable Flame Height Adjustment Inlet Pressure Port ( Millivolt Appliances only) Manifold Pressure Port 1. All Millivolt appliances are equipped with a variable gas control valve.
  • Page 49: Attaching Safety In Operation Warnings

    Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 HOMEOWNER’S INSTRUCTIONS - ATTACHING SAFETY IN OPERATION WARNINGS ATTACHING SAFETY IN OPERATION WARNINGS APPOSITION DES MISES EN GARDE RELATIVES COLOCACIóN DE ADVERTENCIAS DE SEGURIDAD à...
  • Page 50: Maintenance

    Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 MAINTENANCE Replacing Logs WARNING If the logs become damaged by accident or (See Maintenance Schedule, Page 60) Do not use abrasive cleaners improper handling and need replacement, use on glass.
  • Page 51: Front Glass Enclosure Panel, Removal And Installation

    Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 Front Glass Enclosure Panel, Removal Installing Glass Enclosure Panel WARNING and Installation (see Figure 76) Any safety screen, guard, or Retrieve the glass door. Visually inspect the WARNING barrier removed for servicing gasket on the backside of the frame.
  • Page 52: Install Vermiculite, Embers And Logs

    Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 INSTALL VERMICULITE, GLOWING EMbERS AND LOGS NOTE: Turn off all electricity to the appliance before you install vermiculite, embers and logs. bottom View of Logs (in packaging) LOG SET - IDENTIFICATION LOG SET Catalog Number H3210...
  • Page 53 Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 INSTALLATION STEPS: 7. Place Log (B) as shown in Figure 80. READ WARNINGS ON PAGE 54 BEFORE PROCEEDING Position Log (b) Against The back Of The Grate Here 1.
  • Page 54 Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 10. Place Log (E) as shown in Figure 83. WARNING Position The Round End Of Log (E) Against The Notch Of • DO NOT attempt to install the logs until the appli- Log (D) Here.
  • Page 55: Burner Flame Appearance/Sooting

    Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 BURNER ADJUSTMENTS Air Shutter Adjustment Guidelines The following chart is provided to aid you in achieving the correct air shutter adjustment (QUALIFIED TECHNICIANS ONLY) •...
  • Page 56: Burner Flame Adjustments

    Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 BURNER FLAME ADJUSTMENTS Millivolt Appliance Checkout • If flame appears weak or sooty, adjust the air shutter, incrementally, to a The pilot flame should be steady, not lifting more open position until the proper WARNINGS or floating.
  • Page 57: Wiring Diagram

    Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 WIRING DIAGRAM CAUTION: LABEL ALL WIRES PRIOR TO DISCONNECTION WHEN SERVICING Wiring diagrams are provided here for reference CONTROLS. WIRING ERRORS CAN purposes only.
  • Page 58: Accessory Components

    Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 ACCESSORY COMPONENTS Forced Air blower Kits Cat. Model No. Description 80L84 FBK-100 blower, Standard (single speed) 80L85 FBK-200 blower, Variable Speed (w/wall-mounted switch) 80L86 FBK-250 blower, Variable Speed (w/...
  • Page 59 Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 Cost Effective Solution Thermostatic or Manual modes • Simple On/Off operation Flame and Heat modulation • LCD Display • Includes solenoid for SIT millivolt valves •...
  • Page 60: Maintenance Schedule

    Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 MAINTENANCE SCHEDULE Annually (Before the onset of the Burning Season) MAINTENANCE TASK ACCOMPLISHING PERSON PROCEDURE Inspecting/Cleaning Burner, Logs Qualified Service Technician Inspect valve and ensure it is properly operating. Check piping and Controls for leaks.
  • Page 61: Lighting Instructions - Millivolt

    Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 LIGHTING INSTRUCTIONS – MILLIVOLT GAS VALVE FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.
  • Page 62 Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 INSTRUCTIONS D’ALLUMAGE – VANNE GAZ MILLIVOLT POUR PLUS DE SÉCURITÉ, LIRE AVANT D’ALLUMER AVERTISSEMENT. Quiconque ne respecte pas à la lettre les instructions dans la présente notice risque de déclencher un incendie ou une explosion entraînant des dommages, des blessures ou la mort.
  • Page 63: Troubleshooting Guide - Millivolt

    Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 TROUBLESHOOTING THE MILLIVOLT GAS CONTROL SYSTEM NOTE: Before troubleshooting the gas control system, be sure external gas shut off valve (located at gas supply inlet) is in the “ON”...
  • Page 64: Replacement Parts List

    Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 REPLACEMENT PARTS LIST - ST/PF Item Part/Cat.No. Description Where Used Item Part/Cat. No. Description Where Used Misc. Replacement Parts Misc. Replacement Parts H6282 Burner, Pan H3210...
  • Page 65 Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 REPLACEMENT PARTS (PENINSULA SHOWN) Complete log Set Available Only NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
  • Page 66 Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 NOTES ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________...
  • Page 67: Warranty

    THE WARRANTY Innovative Hearth Products ("IHP") 20 Year Limited Warranty warrants your Comfort Flame™ Brand gas fireplace or insert ("Product") to be free from defects in materi- als and workmanship at the time of manufacture. The Product body and firebox carry the 20 Year Limited Warranty. Ceramic glass carries the 20 Year Limited Warranty against thermal breakage only.
  • Page 68 Innovative Hearth Products Installation and Operation Instructions Rochester See Through and Peninsula Direct Vent Gas Fireplace 900476-000, 08/2015 Contact an IHP dealer to obtain any of these parts. Please contact IHP for the phone number of your nearest IHP dealer. ComfortFlame.us.com Record the following important information about your fireplace: Fireplace model number...

This manual is also suitable for:

Rochester pfdmpRochester stdmpRochester pfdmn

Table of Contents