First check and identify the contents of your Or- age to the unit or electrical shock. If a foreign pheus Two package, as listed below : Multimode operation : pure stereo, stereo mul- object should get into the unit, contact your ...
SELECT 3. INFRARED REMOTE CONTROL SENSOR LEFT RIGHT Used for entering menu structure and accessing Receives signals from the remote control menu options as well as confirming choices and transmitter. settings. DOWN SELECT ORPHEUS TWO...
1 and 2. Note - In stereo mode, red and black marked con- Dual multichannel mode : two six channel in- 6. UNBALANCED MAIN OUTPUT nectors are the right and left channels respective- put blocks.
If you wish to wire the balanced output to an unbalanced input (with RCA connector), con- nect pin 1 to ground and pin 2 to signal, and make R : right channel sure pin 3 is not used. L : left channel ORPHEUS TWO...
VCR or DA con- ding equipment, e.g. pendant level control verter tape deck Input for one balanced Parallel main stereo stereo source, e.g. CD output player or DA converter R : right channel L : left channel ORPHEUS TWO...
DVD-V players 1 : main left channel 4 : right surround channel R : right channel 2 : main right channel 5 : center channel L : left channel 3 : left surround channel 6 : subwoofer channel ORPHEUS TWO...
DVD-V players 1 : main left channel 4 : right surround channel R : right channel 2 : main right channel 5 : center channel L : left channel 3 : left surround channel 6 : subwoofer channel ORPHEUS TWO...
D I S P L A Y A N D M E N U S T R U C T U R E Orpheus Two INPUT 1 ||||||||| -40 preamplifier INPUT 2 SETUP> STANDBY SETUP> SETUP> PREFERENCES NAMES SETUP> SETUP>...
S E T U P A N D O P E R A T I O N S QUICK GUIDE ORPHEUS TWO |||||||| - 40 MULTICHANNEL PREAMP POWER ON Flip the main power switch on the left hand side of...
Page 11
Press to confirm the choice and save the new sing < or > until the chosen input is displayed. input name. Characters A to Z and 0 to 9, as well as space, Press to confirm. are available. V W X ORPHEUS TWO...
Page 12
+10.0dB CHANNEL 1: +10.0dB Press to confirm. To increase or decrease the volume level value To increase or decrease the volume level value press or v. press or v. Press to confirm. Press to confirm. ORPHEUS TWO...
Page 13
To set repeat rate pres < or > until the chosen mode is displayed. mode is displayed. Press to confirm. To enter passive filter mode press . Press to confirm. The passive filter is used to reduce high frequen- cy noise generated by multichannel sources. ORPHEUS TWO...
Page 14
Multichannel : stereo Input level : all set at 0.0 dB Channel level : all set at 0.0 dB Names : INPUT 1 to 6, BALANCED and MONITOR Repeat rate : medium Passive filter : Display : 100% ORPHEUS TWO...
OUTPUT 3 OUTPUT 2 MAIN OUTPUT MAIN OUTPUT BALANCED MONITOR OUT right left MUTE MUTE R CHANNEL R CHANNEL R CHANNEL MONITOR L CHANNEL L CHANNEL L CHANNEL WITH MULTICHANNEL INPUT NOT APPLICABLE ORPHEUS TWO...
OUTPUT 3 OUTPUT 2 MAIN OUTPUT MAIN OUTPUT BALANCED MONITOR OUT right left R CHANNEL R CHANNEL R CHANNEL R CHANNEL R CHANNEL MONITOR L CHANNEL L CHANNEL L CHANNEL L CHANNEL L CHANNEL WITH MULTICHANNEL INPUT NOT APPLICABLE ORPHEUS TWO...
118 dBr IMPORTANT NOTICE Residual noise 20 Hz to 22 kHz : Orpheus Media Sàrl reserve the right to make 5.0 V @ 4 Vrms balanced changes to their products or discontinue any pro- 2.5 V @ 2 Vrms unbalanced duct or service without notice.
Need help?
Do you have a question about the Two and is the answer not in the manual?
Questions and answers