Grizzly T10828 Owner's Manual
  1. Manuals
  2. Brands
  3. Grizzly Manuals
  4. Power Tool
  5. T10828
  6. Owner's manual
Grizzly T10828 Owner's Manual

Grizzly T10828 Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
MODEL T10828
ROTARY TOOL WORKSHOP
OWNER'S MANUAL
(For models manufactured since 12/14)
COPYRIGHT © JANUARY, 2015 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#BB17036 PRINTED IN CHINA
V1.01.15

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the T10828 and is the answer not in the manual?

Questions and answers

Related Manuals for Grizzly T10828

Summary of Contents for Grizzly T10828

  • Page 1 (For models manufactured since 12/14) COPYRIGHT © JANUARY, 2015 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. #BB17036 PRINTED IN CHINA V1.01.15...
  • Page 2 This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death.

  • Page 3: Safety Instructions For Power Tools

    Operating tools in when operating or observing machinery to these areas greatly increases risk of acci- reduce the risk of eye injury or blindness from flying particles. Everyday eyeglasses dents and injury. are not approved safety glasses. Model T10828 (Mfd. since 12/14)

  • Page 4: Securing Workpiece

    FORCING TOOLS. Use right tool for job, forming the intended operation, stop and do not force it. It will do job safer and using the machine! Contact our Technical better at rate for which it was designed. Support at (570) 546-9663. Model T10828 (Mfd. since 12/14)
  • Page 5 Use this and other machinery with caution and respect. Failure to do so could result in serious personal injury, damage to equipment or poor work results. Model T10828 (Mfd. since 12/14)

  • Page 6: Section 2: Introduction

    T10828 Rotary Tool we used below. when writing this manual. However, some- times we still make an occasional mistake.
  • Page 7 Identification Become familiar with the names and locations of the controls and features shown below to better understand the instructions in this manual. Figure 1. T10828 component identification. A. Flexible Shaft Collet Nut B. Flexible Locking Sleeve To reduce your risk of C.
  • Page 8 SECTION 3: SETUP Unpacking Inventory Model T10828 Inventory (Figure 2) Your machine was carefully packaged for safe transportation. Remove the packag- A. Toolbox ing materials from around your machine —Collet Wrench .........1 and inspect it. If you discover the machine —Collet...

  • Page 9: Power Connection

    Disconnecting Power 1. Turn machine power switch OFF. 2. Grasp molded plug and pull it com- pletely out of receptacle. Do not pull by the cord as this may damage wires inside. Figure 4. Disconnecting power. Model T10828 (Mfd. since 12/14)

  • Page 10: Section 4: Operations

    1. DISCONNECT TOOL FROM POWER! Operating Rotary Tool 2. Press spindle lock and rotate collet nut The Model T10828 is best suited for high- until spindle locks (see Figure 5). RPM, low-torque applications. Most opera- tions performed with the tool will perform 3.
  • Page 11 1. DISCONNECT TOOL FROM POWER! 2. Loosen collet nut and remove plastic locking ring on rotary tool (see Figure 1 on Page 5) to expose shaft attachment threads, as shown in Figure 6. Figure 7. Tightening flex shaft collet. Model T10828 (Mfd. since 12/14)

  • Page 12: Section 6: Maintenance

    25-30 hours of use. To lubricate flex shaft: 3. Re-install brush cap. Run tool for 5 minutes to seat brushes before using it on a workpiece. 1. Remove inner spindle. Model T10828 (Mfd. since 12/14)

  • Page 13: Section 7: Service

    1. See Installing Bits on Excessive 1. Bit not inserted correctly. Page 8. vibration. 2. Brushes worn. 2. Replace brushes. Motor 1. Dirty or blocked motor vents. 1. Blow out and wipe down overheats. motor vents. Model T10828 (Mfd. since 12/14)

  • Page 14: Parts Breakdown

    AIR DEFLECTOR (R) PT10828014 LOCKING RING PLASTIC PT10828006 CIRCUIT BOARD PT10828015 COLLET PT10828007 TAP SCREW M3 X 8 PT10828016 COLLET NUT PT10828008 CARBON BRUSH (2-PC SET) PT10828017 TAP SCREW M3 X 15 PT10828009 HOUSING (L) Model T10828 (Mfd. since 12/14)

  • Page 15: Warranty

    WARRANTY Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.

Table of Contents