Table of Contents
Advertisement
Quick Links
Warranty
Each Steelcraft unit is thoroughly inspected in our Quality Assurance
department prior to delivery. In the unlikely case that you find any
material or workmanship that affects the units normal operation,
we will repair the unit free of charge within 12 months of purchase.
You are required to present your receipt as proof of purchase.
For all concerns with your product please contact our Customer
Service team.
CUSTOMER SERVICE
1300 303 330 - Australia
0508 688 822 - New Zealand
Please read all the information carefully before using this product.
This warranty does not apply to failure due to improper care,
or normal wear and tear caused by product use. We reserve the
right to inspect the unit. You may be charged for repairs if the
product has been damaged accidentally.
Distributed by:
AUSTRALIA
BRITAX CHILDCARE PTY.LTD.
A Britax International company.
(Incorporated in Victoria)
A.B.N. 55 006 773 600
99 Derby Road, Sunshine,
Victoria 3020, Australia
Phone: (03) 9288 7288
Fax: (03) 9311 5798
Due to our continuing program of development, Britax reserves the right to alter the
specifications, colour or design without any further notice.
The Steelcraft trademark is the property of Britax Childcare Pty. Ltd-Australia.
The Britax trademark is the property of Britax Excelsior Limited - UK.
Visit the Britax website at: http:/www.britax.com.au or email us at custserv@britax.com.au
Due to the variations in the style and design of our products the illustrations used in this
instruction booklet are generic.
12/06 c 2006 Copyright Britax Childcare Pty. Ltd. Australia.
12
NEW ZEALAND
BRITAX CHILDCARE NZ. Limited.
A Britax International company.
101 Diana Drive, Glenfield,
Auckland 9, New Zealand.
Phone: (09) 443 0102
Fax: (09) 443 0120
4000657
KEEP INSTRUCTIONS FOR FUTURE REFERENCE
series AX198
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Steelcraft PROFILE
Summary of Contents for Steelcraft PROFILE
-
Page 1: Customer Service
Due to our continuing program of development, Britax reserves the right to alter the specifications, colour or design without any further notice. The Steelcraft trademark is the property of Britax Childcare Pty. Ltd-Australia. The Britax trademark is the property of Britax Excelsior Limited - UK. - Page 2 CARE AND MAINTENANCE READ THESE INSTRUCTIONS CAREFULLY AND KEEP THEM FOR FUTURE REFERENCE. To prolong the life of your nursery product keep it clean and do not leave it in the direct THE CORRECT USE AND MAINTENANCE OF THIS PRODUCT IS ESSENTIAL. sunlight for extended periods of time.
- Page 3 3. REMOVING THE CARRIER FROM THE STROLLER 1. TO OPEN THE STROLLER Lower the stroller backrest to the full recline Hold the stroller by the handles and release the position. storage latch. Fold the carrier handle up to the carry position Hold the handles and allow the front legs to drop and grip firmly in one hand.
- Page 4 Lift the locking clip up to lock the swivel wheels. NOTE: Do not use the carrier with any other stroller. The swivel wheels can only be locked when the Only use a Steelcraft stroller with the Unity wheels are in the trailing position (wheels under attachment bumper bar.
- Page 5 The carrier must be correctly fitted and locked into the stroller. TO ADJUST THE LEG SUPPORT The carrier must only be used with a Steelcraft stroller with compatible attachments. Lower the leg support by pressing up the release latches located underneath on both sides of the leg In the event of doubt about the method of installation, support.
- Page 6 TO ATTACH AND USE THE CANOPY 11. TO FOLD THE STROLLER Attach the canopy clips to each side of the stroller Remove the boot cover (if fitted), close the frame by pushing the clips until they snap into canopy and place the backrest in the fully upright place.
Need help?
Do you have a question about the PROFILE and is the answer not in the manual?
Questions and answers