Steelcraft CRUISER - SERIES H609 Manual

Steelcraft CRUISER - SERIES H609 Manual

Stroller and travel system

Advertisement

Quick Links

Warranty
Each Steelcraft unit is thoroughly inspected in our Quality Assurance
department prior to delivery. In the unlikely case that you find
any faulty material or workmanship that affects the units normal
operation, we will repair the unit free of charge within 12 months
of purchase. You are required to present your receipt as proof of
purchase. For all concerns with your product please contact our
Customer Service team.

CUSTOMER SERVICE

1300 303 330 - Australia
0508 688 822 - New Zealand
Please read all the information carefully before using this product.
This warranty does not apply to failure due to improper care,
or normal wear and tear caused by product use. We reserve the
right to inspect the unit. You may be charged for repairs if the
product has been damaged accidentally.
Distributed by:
AUSTRALIA
BRITAX CHILDCARE PTY.LTD.
A Britax International company.
(Incorporated in Victoria)
A.B.N. 55 006 773 600
99 Derby Road, Sunshine,
Victoria 3020, Australia
Phone: (03) 9288 7288
Fax: (03) 9311 5798
Due to our continuing program of development, Britax reserves the right to alter the specifications,
colour or design without any further notice.
The Steelcraft trademark is the property of Britax Childcare Pty. Ltd-Australia.
The Britax trademark is the property of Britax Excelsior Limited - UK.
Visit the Britax website at: http:/www.britax.com.au or email us at custserv@britax.com.au
Due to the variations in the style and design of our products the illustrations used in this instruction
booklet are generic.
1/08 © 2008 Copyright Britax Childcare Pty. Ltd. Australia.
20
NEW ZEALAND
BRITAX CHILDCARE NZ. Limited.
A Britax International company.
101 Diana Drive, Glenfield,
Auckland 9, New Zealand.
Phone: (09) 443 0102
Fax: (09) 443 0120
4000941_B
KEEP INSTRUCTIONS FOR FUTURE REFERENCE
Suitable for use with Steelcraft Infant Carrier and Cruiser Bassinet (both sold separately)
series H609

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CRUISER - SERIES H609 and is the answer not in the manual?

Questions and answers

Summary of Contents for Steelcraft CRUISER - SERIES H609

  • Page 1: Customer Service

    Phone: (03) 9288 7288 Fax: (03) 9311 5798 Due to our continuing program of development, Britax reserves the right to alter the specifications, colour or design without any further notice. The Steelcraft trademark is the property of Britax Childcare Pty. Ltd-Australia.
  • Page 2 • The weight of the child using this product should not exceed 17kg. • Do not use accessories other than those supplied and approved by Britax. • When making adjustments to the stroller, ensure that you and your child’s body are clear of any moving parts on the stroller.
  • Page 3: Care And Maintenance

    . Check parts regularly for tightness of screws, nuts and other fasteners, and tighten if required. To maintain the safety of your nursery product, seek prompt repairs for bent, torn, worn or broken parts. Use only those parts and accessories tested and approved by Britax. www.britax.com.au www.britax.com.au...
  • Page 4 Take the left hand Guard and with the hole in the moulding to the inside. Have the long Guard section pointing to the rear. Push the Guard up onto the rear leg until it locks on. Repeat for the right hand side. www.britax.com.au www.britax.com.au...
  • Page 5: To Fit And Remove The Rear Wheels

    Ensure the bassinet To release the brake, lift the brake is locked on by trying to pull up. lever up. To remove bassinet from stroller firmly lift up and unlock main lever. www.britax.com.au www.britax.com.au...
  • Page 6 To assemble bassinet, extend the bassinet frame support rods by slowly sliding centre of each bar outward until they lock under all 4 clips. Push down lightly on the top edges of the bassinet to check that they are locked in place. www.britax.com.au www.britax.com.au...
  • Page 7: To Release The Infant Carrier

    Lift and remove the Infant Carrier away Squeeze both tabs up and lift the seat out from the stroller frame. of the frame. Squeeze and hold both tabs up and lift the seat out of the frame. www.britax.com.au www.britax.com.au...
  • Page 8: To Fit The Armbar

    To remove the armbar, press in and hold the buttons under each moulding and pull By pushing in and holding the latches on out the armbar pins. either side of the handle, rotate the handle backwards. The GREEN Indicator will now turn to RED. www.britax.com.au www.britax.com.au...
  • Page 9: Canopy Window

    17. TO FOLD THE FRAME 11. TO FIT, ADJUST AND REMOVE THE CANOPY NOTE: If the seat is in the rearward facing Align the canopy mouldings to each side position, it should be removed from the frame of the frame moulding as shown. Push in before folding.
  • Page 10: To Use The Tether Strap

    15. TO USE THE TETHER STRAP 13. TO ADJUST THE FOOTREST AND HANDLE HEIGHT To adjust the footrest, press in and hold WARNING: Use the tether strap to prevent the the buttons on either side of the footrest. stroller from rolling away. At the same time adjust to the desired position.

Table of Contents