Advertisement
Specifications, frequency response & Thiele/Small Parameters
Specifications
Type
6.5cm cone shaped full range
Impedance
8Ω
Lowest resonance freq.
157Hz
Frequency response
f0 ~ 20kHz
Sound pressure level
84dB/w(1m)
Input (Mus.)
15W
m0
1.8g
Q0
0.99
Effective vibration radius
2.6cm
Magnet mass
74g
Gross mass
249g
Baffle hole dimension
Ø60 (Ø58) *Refer to the baffle hole dimen-
sion drawings.
Standard enclosure type
Bass reflex type
Wood screw x 4pcs, Washer x 4pcs
Accessories
Thiele/Small Parameters
Size
65
mm
2.6
Overall Diameter
65
mm
2.6
Baffle Hole Diameter
60
mm
2.4
Depth
38.2
mm
1.5
Voice Coil Diameter
20
mm
0.8
Cast / Stamped
Stamped
Impedance
8
ohm
Reproduction Freq. Response
fs-20
kHz
Sound Pressure Level
84
dB/W (m)
Rated Input
5
W
Music Power
15
W
Magnet Weight
74
g
0.163
Net Weight
249
g
0.549
Equivalent Diaphragm Radius
a
26
mm
Effective Cone Diameter
D
52
mm
Surface Area of Cone
Sd
0.0021
m2
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER - SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING:
To reduce the risk of fire or electric shock, do not expose apparatus to
rain or moisture.
IMPORTANT SAFETY INSTRUCTIONS
1.
Read these instructions.
2.
Keep these instructions.
3.
Heed all warnings.
4.
Follow all Instructions.
5.
Do not use this apparatus near water.
6.
Clean only with dry cloth.
7.
Do not block any ventilation openings. Install in accordance with the manufactur-
er's instructions.
8.
Do not install near any heat sources such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that produce heat.
9.
Do not defeat the safety purpose of the polarized or grounding type plug. A
polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade or the third
prong are provided for your safety. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete outlet.
10.
Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11.
Only use attachments/accessories specified by the
manufacturer.
12.
Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/ap-
paratus combination to avoid injury from tip-over.
FOSTEX CO.
1-1-109, Tsutsujigaoka, Akishima City, Tokyo, 196-8550, Japan
Frequency response
110
100
90
80
70
60
50
Impedance
40
20
[Hz]
50
100
200
500
1k
2k
5k
P650K＋P650-E
110
100
90
80
70
60
50
Impedance
40
30
20
[Hz]
50
100
200
500
1k
2k
5k
Nominal Impedance
Zn
8
ohm
in
Resonance Frequency
Fs
157
Hz
in
DC Resistance
Re
7.3
ohm
in
in
Coil Inductance
Le
0.25
mH
in
Mechanical Q
Qms
3.39
Electromagnetic Q
Qes
1.4
Total Q
Qts
0.99
Equivalent Mass
Mms
1.8
g
BL Product (Factor Force)
BL
3.06
Tesla/m
Compliance Equivalent Volume
Vas
0.35
L
Voice Coil Overhang
Xmax
0.5
mm
lb
Reference Efficiency n0
Eff/n0
0.1
%
Mechanical Compliance of
Cms
0.576
m/N
lb
Suspension
Efficiency Bandwidth Product
EBP
112.143
The lightning flash with arrowhead symbol, within an equilat-eral
triangle, is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
Avertissement:
Pour réduire le risque d'incendie ou de choc électrique, ne pas exposer
cet appareil sous la pluie et l'humidité.
13.
Unplug this apparatus during lightning storms or when unused for long periods
of time.
14.
Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or
has been dropped.
The apparatus shall be used in an open area.
15.
Apparatus shall not be exposed to dripping or splashing and that no objects filled
16.
with liquids, such as vases, shall be placed on apparatus.
Mains plug is used as disconnect device. It shall remain readily operable and
17.
should not be obstructed during intended use. To completely disconnect the
apparatus from supply mains, the mains plug of the apparatus shall be
disconnected from the mains socket outlet completely.
PRINTED IN CHINA AUGUST 2014
P650K
64
32
16
8
FULL RANGE SPEAKER UNIT
4
10k
20k
50k
64
32
16
8
4
10k
20k
50k
P650K
Thank you for purchasing P650K.
Read through this manual so that you can correctly use it.
Dimensions
65
Plus terminal
4-Ø4.5 hole
(#205)
Recommended enclosure
For the easy start, we recommend a combination with a P650-E
enclosure kit. The P650-E is designed for the P650K that can
easily achieve the enticing full range speaker system. The
P650-E comes with the speaker terminals, internal wirings and
sound absorbent pre-fitted and acoustically tuned. Please use the
P650-E taking advantage of easy mount.
To enhance the low frequency more than P650-E, we recommend
the use of P1000-E. As the internal volume is larger, you can feel
low frequency more. In this case, since P650K cannot be mounted
directly, prepare the baffle board as shown in the drawing on the
right. The board material is MDF with t9 thickness, the baffle hole
is 60mm diameter. As the screw position is made as φ116, you
can easily replace the speaker driver with P1000K.
592561
The P650K is a suitable full range speaker driver especially for
first time craft users. A light-weight cone paper and a high-loss
rubber surrounding realize a bright and clear mid-to-high range
and reasonably damped low range reproduction. You can enjoy an
excellent stereo image and sound field achieved by the small-di-
ameter speaker unit.
P650K Main Features
* Banana pulp blended light-weight cone paper / High-loss
foamed rubber surrounding
Blending a banana pulp with two wooden pulps holding differ-
ent physicality realizes a sufficient stiffness and high-loss. A
high-loss foamed surrounding with an up-roll shape is
employed.
* Mechanical 2-way center cap
The same material as the cone paper is employed on the center
cap for improving the sound unification. A mechanical 2-way
structure which directly connects the center cap with the voice
coil bobbin extends a high range sound reproduction further.
Baffle hole dimensions
The baffle hole should be shaped according to board thickness as
shown in the drawings below. If you solder the cable directly to
Minus terminal
(#110)
the speaker terminal, shape the hole as in the right side drawing
with φ58 hole.
Board thickness t9mm or below
Ø55
Ø57.8
Terminal escape cut
Baffle hole dimensions to mount the P1000-E
Board material: MDF t9
Owner's Manual
Board thickness t9mm or more
30
110
4-Ø5 hole
Advertisement
