Operation - Dimplex BLF7451 Service Manual

Hide thumbs Also See for BLF7451:
Table of Contents

Advertisement

OPERATION

Figure 1
Floating
Display
WARNING: This electric firebox must be properly in-
stalled before it is used.
The unit can be controlled by either the manual controls
which are located on the upper right of the fireplace or the
remote (Figure 1 & 2).
The fireplace is supplied with an IR multifunction remote
control.
! NOTE: To operate correctly, the remote control must be
pointed towards the Floating Display
A .
Standby
Turns the unit On and Off.
→ Activated by pressing the Standby button on the remote
or the unit.
• The unit will turn on with the same functions that it was
set to when it was turned Off and the intake temperature
will be indicated on the Floating Display
! NOTE: When any button is pressed the intake tem-
perature will be displayed on the Floating Display
seconds.
B .
Flame Effects
Turns the flame effect On and Off.
→ Activated by pressing the
C .
Heat ON/OFF
Turns the heater On and Off.
→ Activated by pressing the
remote.
• Indicated by the
icon and the intake temperature be-
ing displayed on the Floating Display
before turning off.
! NOTE: After the heater is switched off, there is a 60
second fan delay, where the fan will continue running be-
fore turning off.
! NOTE: The unit can be operated in Heat Only Mode.
When the unit is only running with the heater, the
will continuously be displayed on the Floating Display
! NOTE: The heater may emit a slight, harmless odor
when first used. This odor is a normal condition caused
A
C
D
TM
.
TM
.
TM
TM
button on the remote.
button on the unit or the
, for 5 seconds
TM
by initial heating of internal heater parts and will not occur
again.
E
F
D & E .
Thermostat Controls
Adjusts the temperature set point to your individual require-
ments. Once the desired set temperature is reached the
heater will turn off. The heater will cycle on and off to main-
tain the desired set temperature. The default temperature
setting is 72°F (22°C).
→ Adjusted by pressing the
and the
remote.
• The Floating Display
point as it is adjusted.
! NOTE: Holding the
two seconds, on the unit, will change the temperature from
°C to °F, or vice versa.
Disable Heat
If desired, depending on the season, the heater on the unit
can be disabled. The unit will operate in the same fashion,
with remainder of the controls.
Pressing the
time and holding for 2 seconds will disable and enable the
heater.
! NOTE: When the heater has been disabled and either
the
or the
indicate "--".
F .
Color Themes
Different presets of ambient lighting color combinations
contained in the unit.
for 5
→ Changed by repeatedly pressing the corresponding but-
ton on the remote or the unit.
• Cycles through the different preset ambient lighting set-
tings of the unit, this includes different combinations of
colours of the flame base and media lighting.
! NOTE: The last theme of the cycle is a prism where the
unit cycles through a variety of
colours. Pressing the
stops the cycling and holds the
unit on the preferred color, indi-
cated by a "U" - Unfreeze or a "F"
- Freeze on the display.
G .
Brightness
Changes the brightness of the
lights in the unit.
→ Adjusted by repeatedly press-
ing the corresponding button on
the remote.
icon
.
TM
• Indicated by the second digit on
the Floating Display™ changing
to show: "H" (high), and "L"
to decrease the set point
to increase the set point on the unit or the
will indicate the temperature set
TM
and the
and
buttons on the unit at the same
is pressed the Floating Display
Figure 2
button
A
B
D
F
buttons down for
will
TM
C
E
G
H
3

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents