Related Manuals for WebGate C1080PT-Z20
Summary of Contents for WebGate C1080PT-Z20
- Page 1 HD-SDI PTZ CAMERA (C1080PT-Z20) User’s Manual Ver. 1.0 Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for future reference.
- Page 2 Safety Information CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN. CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Warning Precaution This symbol indicates that dangerous voltage This exclamation point symbol is intended to alert the consisting a risk of electric shock is present within user to the presence of important operating and...
-
Page 3: Important Safety Instructions
Important Safety Instructions Read these instructions. - All these safety and operating instructions should be read before the product is installed or operated. Keep these instructions. - The safety, operating and use instructions should be retained for future reference. Heed all warnings. - All warnings on the product and in the operating instructions should be adhered to. Follow all instructions. - Page 4 Disposal of Old Appliances 1. When this crossed-out wheel bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC. 2. All electrical and electronic products should be disposed of separately form the municipal waste stream stream in accordance to laws designated by the government or the local authorities.
-
Page 5: Table Of Contents
Contents 4 Precautions 1. Introduction Product & Accessories Parts Name & Functions_Appearance Parts Name & Functions_Inside 2. Installation Installation DIP Switch Setup Cabling 3. OSD Menu Check Points before Operation OSD Information General Rules of Menu Operation ROOT MENU & SYSTEM INFORMATION DISPLAY SETUP MOTION SETUP >... -
Page 6: Introduction
Introduction - Product & Accessories Please check if all the camera and accessories are included in the package. Product Accessories Housing Safety Waterproof Tape Cable Hanger Hexagonal Wrench Anchor Bolt(4pcs) Wall Mount Type 10 2. Mount Template Sheet Manual CD Safety Wire Quick Manual Ceiling Mount Type... -
Page 7: Parts Name & Functions_Appearance
Introduction - Part Name & Functions_Appearance Wall/Ceiling Mount Bracket These are used to install the camera on the wall or ceiling and have junction box. Housing Safety Wire Hanger Wall Mount Bracket Ceiling Mount Bracket Sunshield & Upper Housing PTZ Mechanism Sunshield &... -
Page 8: Parts Name & Functions_Inside
Introduction - Part Name & Functions_Inside Test Video Output Connector Video Output Cable DIP Switch for Alarm Output Slot Camera ID Setup DIP Switch for Communication Alarm Input Slot Setup RS-485 Slot Power Slot Heater Video Output Cable Test Video Output Connector Connects to video output device such as monitor using the Video out check the screen during installation. - Page 9 Installation - Installation Using Wall/Ceiling Mount Bracket Wall Mount Bracket Installation Ceiling Mount Bracket Installation Using the mount template sheet, mark the holes on the wall or ceiling. After drilling the holes, fix the four anchor bolts into the holes. Place the wall/ceiling mount bracket on the anchor bolts properly and tighten the nuts on the anchor bolts.
-
Page 10: Installation
Installation - Installation Detach the PTZ mechanism from the upper housing to plug the main cable. When detaching the PTZ mechanism, press down and hold up the black handles on both sides of the PTZ mechanism. Remove the protecting tape used to fix the PTZ mechanism. - Page 11 Installation - Installation Connect each of the following cables to the applicable slots and set the DIP switch to configure the camera ID and communication protocol. Video Output Cable Alarm Input Slot Alarm Output Slot DIP Switch for Camera ID Setup DIP Switch for Communication Setup RS-485 Slot Power Sot...
- Page 12 Installation - Installation Align ‘A’, ’B’ mark of one touch connector in the upper housing with the two black handles of PTZ mechanism, and insert the PTZ mechanism into hook in the upper housing. To lock the PTZ mechanism to the upper housing, press the two black handles until a snap sound is heard.
- Page 13 Installation - Installation Close the dome cover. Match the arrow mark on the dome cover and the housing. Arrow Mark Arrow Mark Tighten four screws on the dome cover in the sequence shown in the image below. To maintain the best sealing, the torque of each screw must be in the range of 0.5 ~ 1.0 N·m(0.3 ~ 0.73 lbf·ft).
-
Page 14: Installation Dip Switch Setup
Installation - DIP Switch Setup Before installing the camera, set up the DIP - When the communication protocol setting is ‘Auto’, camera will recognize SAMSUNG-E or PELCO-D / P protocol switch to configure the Camera ID, automatically. communication protocol, located on the Any other DIP switch combinations will be recognized as Auto mount. - Page 15 Installation - DIP Switch Setup 2. Communication Baud Rate Setup 3. RS-485 Termination Resistor Select the appropriate baud rate with DIP switch combination. 2400 BPS - Factory Default - Pin 8 is used for on/off of RS-485 termination. - Normally, it must be OFF. - When you have trouble with long daisy chain style 4800 BPS connections, turn ON this termination switch on the last...
-
Page 16: Cabling
Installation - Cabling Video Output Power RS-485 Test Video Output (Keyboard Controller/DVR) Video Output RS-485 Communication (Keyboard Controller/DVR) Connects to video output device such as a monitor using a To control multiple PTZ cameras at the same time, the BNC coaxial cable. RS-485 communication lines should be connected in parallel form as shown below. - Page 17 Installation - Cabling Alarm Input Alarm Output In 1 In 8 Alarm Input/Sensor Alarm Output Sensor Input/Sensor Alarm Output - It connects to IR sensor, IrDA sensor or door switch. If - It connects to the alarm lights, siren or lamps, and it is the sensor is activated, it can be activated to move a activated according to the OSD menu setting.
-
Page 18: Osd Menu
OSD - Check Points before Operation Check Points before Operation 1. Before power is applied, please check the cables carefully. 2. The camera ID of the controller must be identical to that of the camera to be controlled. The camera ID can be check in the system information of OSD menu. -
Page 19: Osd Information
OSD - OSD Information CAM 1 31/NOV/2O11 23:59:59 Camera ID Date / Time PRESET 1 Action Title 123.O/45.O/x1.O Alarm I/O Information Pan Angle Tilt Angle Zoom Magnification <OSD on Left Up Side of Monitor Screen> Camera ID Date / Time - The current camera ID(Address). -
Page 20: General Rules Of Menu Operation
OSD - General Rules of Menu Operation This page explains how to operate the OSD menu using ROOT MENU keyboard controller. If there are no keys or functions described ==================================================== <SYSTEM INFORMATION> below, refer the manual of the keyboard controller. <DISPLAY SETUP>... -
Page 21: Root Menu & System Information
OSD - ROOT MENU & SYSTEM INFORMATION ROOT MENU ROOT MENU ==================================================== <SYSTEM INFORMATION> <SYSTEM INFORMATION> <DISPLAY SETUP> Shows information and current configuration. <MOTION SETUP> <FUNCTION SETUP> <DISPLAY SETUP> <CAMERA SETUP> Enable/Disable of OSD informations display on main screen. <SYSTEM SETUP> <MOTION SETUP>... -
Page 22: Display Setup
OSD - DISPLAY SETUP DISPLAY SETUP <DISPLAY SETUP> This menu defines enable/disable of OSD display on main screen. ==================================================== CAMERA ADDRESS If an item is set to be ‘AUTO’, the item is displayed for 3 seconds PTZ INFORMATION when the value of it is changed. ACTION TITLE DATE/TIME CAMERA ADDRESS... -
Page 23: Motion Setup > Alarm Input Setup
OSD - MOTION SETUP > ALARM INPUT SETUP MOTION SETUP <MOTION SETUP> Setup the general functions of pan/tilt motions. ==================================================== POWER UP ACTION JOG MAX SPEED 9O/SEC PWR UP ACTION ON / OFF JOG DIRECTION NORMAL This function enables to resume the last action executed before power <ALARM INPUT SETUP>... -
Page 24: Motion Setup > Parking Action Setup
OSD - MOTION SETUP > PARKING ACTION SETUP PARKING ACTION SETUP <MOTION SETUP> If ‘PARK ENABLE’ is set to ‘ON’, camera runs assigned function ==================================================== POWER UP ACTION automatically if there is no PTZ command during assigned JOG MAX SPEED 9O/SEC ‘WAIT TIME’. -
Page 25: Function Setup > Preset Setup
OSD - FUNCTION SETUP > PRESET SETUP FUNCTION SETUP <FUNCTION SETUP> Configure 4 special functions with this menu. ==================================================== <PRESET SETUP> <SCAN SETUP> PRESET SETUP <PATTERN SETUP> <GROUP SETUP> 255 presets from the number 1 to 255 can be assigned excluding preset 95, 131~134, 141~148, 151~158 reserved for menu. -
Page 26: Function Setup > Scan Setup
OSD - FUNCTION SETUP > SCAN SETUP SCAN SETUP <FUNCTION SETUP> Up to 8 scans are available, which makes the camera to move ==================================================== <PRESET SETUP> slowly between two preset positions. <SCAN SETUP> <PATTERN SETUP> When scan function runs, the camera moves from the preset <GROUP SETUP>... -
Page 27: Function Setup > Pattern Setup
OSD - FUNCTION SETUP > PATTERN SETUP PATTERN SETUP <FUNCTION SETUP> Pattern function is that a camera memorizes the path (mostly ==================================================== <PRESET SETUP> curve path) by joystick of controller for assigned time and <SCAN SETUP> revives the path exactly as it memorized. <PATTERN SETUP>... -
Page 28: Function Setup > Group Setup
OSD - FUNCTION SETUP > GROUP SETUP GROUP SETUP SCREEN <FUNCTION SETUP> The group function allows running sequence of presets, pattern ==================================================== <PRESET SETUP> and/or scans. Max. 8 group can be stored. Each group can have <SCAN SETUP> max. 20 action entities which can be preset, pattern or scan. <PATTERN SETUP>... - Page 29 OSD - FUNCTION SETUP > GROUP SETUP EDIT GROUP - Assign Function <EDIT GROUP> Move cursor to the ‘NO.’ to assign the function, press the ‘NEAR’ ==================================================== ACTION Dwell key to set up. Select the function by moving joystick up/down. ==================================================== NONE NONE...
-
Page 30: Camera Setup > White Balance Setup
OSD - CAMERA SETUP > WHITE BALANCE SETUP CAMERA SETUP <CAMERA SETUP> Setup the general functions of zoom camera module. ==================================================== FOCUS MODE AUTO DIGITAL ZOOM FOCUS MODE AUTO / MANUAL STABLE ZOOM Sets the camera focus mode. <WHITE BALANCE SETUP> <AUTO EXPOSURE SETUP>... -
Page 31: Camera Setup > Auto Exposure Setup
OSD - CAMERA SETUP > AUTO EXPOSURE SETUP AE SETUP <CAMERA SETUP> ==================================================== BACK LIGHT ON / OFF FOCUS MODE AUTO DIGITAL ZOOM Sets the backlight compensation. STABLE ZOOM <WHITE BALANCE SETUP> DAY/NIGHT AUTO / DAY / NIGHT <AUTO EXPOSURE SETUP> ‘AUTO’... -
Page 32: Camera Setup > Other Setup
OSD - CAMERA SETUP > OTHER SETUP OTHER SETUP <CAMERA SETUP> ==================================================== EXP COMPENSATION 7 (GAIN:-10.5dB) FOCUS MODE AUTO DIGITAL ZOOM ~ +7 (GAIN:+10.5dB) (15 Steps) STABLE ZOOM Default is ‘0/0dB’. <WHITE BALANCE SETUP> <AUTO EXPOSURE SETUP> APERTURE 0 ~ 15 <OTHER SETUP>... -
Page 33: Camera Setup > Privacy Zone Setup
OSD - CAMERA SETUP > PRIVACY ZONE SETUP PRIVACY ZONE SETUP <CAMERA SETUP> ==================================================== MASK NUMBER 1 ~ 8 FOCUS MODE AUTO DIGITAL ZOOM Select mask number. If the selected mask has data already, camera STABLE ZOOM moves as it was set. Otherwise, ‘UNDEFINED’ will be displayed under <WHITE BALANCE SETUP>... -
Page 34: System Setup
OSD - SYSTEM SETUP SYSTEM SETUP <SYSTEM SETUP> ==================================================== HD-SDI 1280x720p50 / 1280x720p60 / 1920x1080i50 / HD-SDI 192Ox1O8Oi6O CLEAR ALL DATA CANCEL 1920x1080i60 / 1920x1080p25 / 1920x1080p30 AUTO CALIBRATION CANCEL Select the resolution of HD-SDI. <DATE/TIME> CLEAR ALL DATA CANCEL / OK Deletes all configuration data such as display, camera, motion setup and so on. -
Page 35: Specifications
Specifications - Dimension Unit: mm 182.5 3/4” PIP THREAD 78.7 404.5 Wall Mount Bracket 182.5 3/4” PIP THREAD 3/4” PIP THREAD 78.7 Ceiling Mount Bracket...
Need help?
Do you have a question about the C1080PT-Z20 and is the answer not in the manual?
Questions and answers