Advertisement
MENU "1/2/3/4/5/6 Output Channels Editing" [Access by pushing the "1/2/3/4/5/6" buttons]
NAV/PAR1 Encoder
[to navigate between menus]
1. Output [x] [Name]
HPF
20.0 Hz
No Cut-Off
ESC
ENTER
-> 20.0 Hz
No Cut-Off
2. Output [x] [Name]
LPF
20.0 Hz
No Cut-Off
ESC
ENTER
-> 20.0 Hz
No Cut-Off
3.
Output [x] [Name]
1.00kHz
BW/SHV_Slope=1.00/up to -12dB
ESC
ENTER
If through the PM2, being the filter's gain = 0.0dB,
has been selected a
Bell filter
BW to be greater then 0, then the Bell filters can be set by
the following parameters
3.1 Output[x]
[Name]
-> 1.00kHz BW=1.00 +0.0dB
If through the PM2, being the filter's gain = 0.0dB,
has been selected a
Low Shelving
Slope (1
st
or 2
nd
order available, -6dB or -12dB), then the
Low Shelving filter can be set by the following parameters
3.2 Output[x]
[Name]
-> 1.00kHz (-6/-12)LoSh
+0.0dB
If through the PM2, being the filter's gain = 0.0dB,
has been selected a
High Shelving filter
Slope (1
st
or 2
nd
order available, -6dB or -12dB), then the
High Shelving filter can be set by the following parameters
3.3 Output[x]
[Name]
-> 1.00kHz (-6/-12)HiSh
+0.0dB
4. Output [x] [Name] Vu-Meter
Vu-Meter = Level
ESC
ENTER
-> Vu-Meter = Level
5. Output [x] [Name] Name
Name = [Name]
ESC
ENTER
-> Name = _
PEQ/SHV - 1/7
+ 0.0dB
, just defining its Bandwidth
EQ-X (up to 7 filters available)
filter, just defining its
EQ-X (up to 7 filters available)
, just defining its
EQ-X (up to 7 filters available)
NAV/PAR1 Enc .
[to chose values for the parameters, no need to confirm the chosen values,
which are automatically loaded during the encoders use]
PAR1 N/A
PAR1 N/A
(when the filter's gain = 0.0dB ONLY, through the PM2 it is possible to
chose and select between a Bell or a Shelving filter)
[Freq.] 20Hz
:
20kHz
[Freq.]
20Hz
:
20kHz
[Freq.] 20Hz
:
20kHz
PAR1 N/A
(For Editing the Device's Name, refer to the
7
PM2 Enc.
PM3 Enc.
[Freq.] 20Hz
[Type/Slope] No Cut-Off
:
20kHz
Bessel 24dB/Oct
[Freq.] 20Hz
[Type/Slope] No Cut-Off
:
20kHz
Bessel 24dB/Oct
[BW] 0.05
:
3.00
PM2 N/A
PM2 N/A
Level
Same as PAR2
Limiter Act.
Details on the"Utility Menus Use"
:
:
[Amp.] -15.0 dB
:
+15.0 dB
[Amp.]
-15.0 dB
:
+15.0 dB
[Amp.] -15.0 dB
:
+15.0 dB
Section)
Advertisement
