Table of Contents
Advertisement
2 . 2 .
2 .
2 .
2 .
C P U f a n p i n s e l e c t i o n ( 3 - p i n F M _ C P U 1 , F M _ C P U 2 )
C P U f a n p i n s e l e c t i o n ( 3 - p i n F M _ C P U 1 , F M _ C P U 2 )
C P U f a n p i n s e l e c t i o n ( 3 - p i n F M _ C P U 1 , F M _ C P U 2 )
C P U f a n p i n s e l e c t i o n ( 3 - p i n F M _ C P U 1 , F M _ C P U 2 )
C P U f a n p i n s e l e c t i o n ( 3 - p i n F M _ C P U 1 , F M _ C P U 2 )
These jumpers allow you to connect either a 3-pin or a 4-pin fan cable
plug to the CPU fan connectors (CPU_FAN1, CPU_FAN2). Set these
jumpers to pins 1-2 if you are using a 3-pin fan cable plug, or to pins 2-3
if you are using a 4-pin plug.
PVL-D/1U/SCSI FM_CPU setting
3 .
3 . 3 .
U S B d e v i c e w a k e - u p ( 3 - p i n U S B P W 1 2 , U S B P W 3 4 )
U S B d e v i c e w a k e - u p ( 3 - p i n U S B P W 1 2 , U S B P W 3 4 )
3 .
3 .
U S B d e v i c e w a k e - u p ( 3 - p i n U S B P W 1 2 , U S B P W 3 4 )
U S B d e v i c e w a k e - u p ( 3 - p i n U S B P W 1 2 , U S B P W 3 4 )
U S B d e v i c e w a k e - u p ( 3 - p i n U S B P W 1 2 , U S B P W 3 4 )
Set these jumpers to +5V to wake up the computer from S1 sleep mode
(CPU stopped, DRAM refreshed, system running in low power mode)
using the connected USB devices. Set to +5VSB to wake up from S4
sleep mode (no power to CPU, DRAM in slow refresh, power supply in
reduced power mode).
PVL-D/1U/SCSI USB device wake up
•
The USB device wake-up feature requires a power supply that can
provide 500mA on the +5VSB lead for each USB port; otherwise, the
system would not power up.
•
If you are using Windows 2000, you need to install Service Pack 4 to
wake up the system from S4 sleep mode.
•
The total current consumed must NOT exceed the power supply
capability (+5VSB) whether under normal condition or in sleep mode.
A S U S R S 1 6 0 - E 3 / P S 4
A S U S R S 1 6 0 - E 3 / P S 4
A S U S R S 1 6 0 - E 3 / P S 4
A S U S R S 1 6 0 - E 3 / P S 4
A S U S R S 1 6 0 - E 3 / P S 4
FM_CPU1
3
2
2
1
DC mode
PWM
(Default)
FM_CPU2
3
2
2
1
DC mode
PWM
(Default)
USBPW12
3
2
2
1
+5V
+5VSB
(Default)
USBPW34
1
2
2
3
+5VSB
+5V
(Default)
4 - 5
4 - 5
4 - 5
4 - 5
4 - 5
Advertisement
Table of Contents
