ZKTeco ma 300 Installation Manual

Installation Guide
1.Equipment Installation
Mounting Paper(only for your reference)
10
11
line hole
12
13
(2)Remove the screw on the
(1)Post the mounting template on the wall.
Drill the holes according to the marks on the
template (holes for screw and wiring).
(4)Fix the back cover and waterproof pad on the
wall according to the mounting paper.
(5)Set the device to the fixed waterproof pad.
2. Structure and Function
⑥ ⑥
RS485 RS485 TCP/IP TCP/IP
RS232/RS485
Converter
① ① ② ②
Lock
门锁 Door Sensor
⑤ ⑤
④ ④
Card Reader Exit Button
③ ③
Alarm
(3)Take away the back cover and
waterproof pad.
bottom of device.
(6)Fix the device to the back cover.
Access Control System Function:
(1)If a registered user verified, the device will export the
signal to unlock the door.
(2)Door sensor will detect the on-off state. If the door is
unexpected opened or improperly closed, the alarm
signal (digital value) will be triggered.
(3)If the device being illegally removed, the device will
export alarm signal.
(4)External card reader is supported.
(5)External exit button is supported; it is convenient to
open the door inside.
EXIT
(6)Supports RS485, TCP/IP modes to connect with PC.
One PC can manage multiple devices.
Version: 1.1
3.Lock Connection
Date: Dec. 2010
(1) The system supports NO LOCK and NC LOCK. For example the NO LOCK (normally open at power on) is connected with
'NO' terminal, and the NC LOCK is connected with 'NC' terminal.
(2) When the Electrical Lock is connected to the Access Control System, you need to parallel one FR107 diode (equipped
in the package) to prevent the self-inductance EMF affect the system, do not reverse the polarities.
(I)Share power with the lock:
+
-
DC12V
NC LOCK -
+
(II)Does not share power with the lock:
+
-
DC12V
+
-
DC Power
+
FR 107
NO LOCK
①: 'I': device output current, 'U
4.Connected with Other Parts:
EXIT
Exit Button
-
+
Alarm Power Alarm
Voltage output ≤ DC 12V for Alarm
！
Warning: No operating with power on!
+
+12V
+12V
GND
- GND
485-
485-
485+
DC12V 485+
GND
GND
NO LOCK
BUT
- BUT
SEN
SEN
FR 107
NO
NO
+
COM
COM
FR 107
NC
NC
AL-
AL-
AL+
AL+
+
+12V
-
GND
DC12V
-
485-
485+ FR 107
GND
+
BUT
NC LOCK
-
SEN
NO
COM
+
NC
AL-
DC Power
AL+
': lock voltage,' I ': lock current.
LOCK LOCK
5.Connected with Power:
485-
485+
GND
BUT
+
SEN
-
NO
COM
DC12V
NC
Door Sensor
AL-
AL+
Input DC 12V, 500mA (50mA standby)
Positive is connected with '+12V', negative is connected
with 'GND' (do not reverse the polarities).
Device share power with the lock:
>1A...... ①
U =12V, I-I
LOCK LOCK
And the lock is near to the device.
+12V
GND
485-
Device does not share power with the lock:
485+
≤1A;
A. U =12V I- I
LOCK LOCK
GND
B ≠12V;
. U
BUT
LOCK
SEN
C. The lock is far apart from the device.
NO
COM
NC
AL-
AL+
+12V
GND