Zenoah PSZ2610 Owner's Manual
  1. Manuals
  2. Brands
  3. Zenoah Manuals
  4. Pole Saw
  5. PSZ2610
  6. Owner's manual
Zenoah PSZ2610 Owner's Manual

Zenoah PSZ2610 Owner's Manual

Hide thumbs Also See for PSZ2610:
Table of Contents

Advertisement

Quick Links

Download this manual
115 40 43-38 (011)
G
B
OWNER'S MANUAL
POLE SAW
PSZ2610

Advertisement

Table of Contents
loading

Related Manuals for Zenoah PSZ2610

Summary of Contents for Zenoah PSZ2610

  • Page 1 115 40 43-38 (011) OWNER’S MANUAL POLE SAW PSZ2610...

  • Page 2: Table Of Contents

    PSZ2610 Contents SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into 1. Parts location ...........2 consideration to prevent possible serious bodily injury, and for 2. Specifications ...........3 this reason you are requested to read all such instructions care- 3.

  • Page 3: Specifications

    Idle speed ....3000±200min-1(rpm) Oil pump ..........Plunger type Fuel ....Mixture (Gasoline 50 : Oil 1) Standard Accessories (when using ZENOAH genuine oil) Harness .............. 1 pc. Carburetor ....Walbro Diaphragm type Tool Kit ..............1 pc. Spark plug ........ NGK CMR7H Guide bar cover ..........

  • Page 4: For Safe Operation

    PSZ2610 5. For safe operation WORKING PLAN 1. Read this manual carefully until you 1. You should never use the product completely understand and follow all when under the influence of alcohol, safety and operating instructions. when suffering from exhaustion or lack 2.
  • Page 5 Cut only materials recommended by the be sure to use only ZENOAH prod- manufacturer. And use only for tasks explained in the manual. ucts or products which have been certified by ZENOAH for use with 1.
  • Page 6 PSZ2610 5. For safe operation HANDLING FUEL must take several steps to keep your 1. The engine of the ZENOAH product jobs free from accident or injury: is designed to run on a mixed fuel, which contains highly flammable 1. Understand kickback and pinching! gasoline.

  • Page 7: Set Up

    PSZ2610 6. Set up MOUNTING ENGINE 3. Insert the end of the tube into transmission. 4. Line up the hole on the end of the transmission into which the bolt is to be inserted with the screw hole on the tube, and screw the bolt firmly in.
  • Page 8 PSZ2610 6. Set up 4. Adjust the chain tension by turning the chain tension HOW TO WEAR adjuster screw until the tie straps just touch the bot- 1. Wear the provided harness without twisted bands, tom side of the bar rail.

  • Page 9: Fuel And Chain Oil

    2. Put fuel into the fuel tank to 80% of the full capacity. 3. Fasten the fuel cap securely and wipe up any fuel spillage around the unit. • The Zenoah engines are lubricated by oil specially WARNING formulated for air-cooled 2-cycle gasoline engine use.

  • Page 10: Operation

    PSZ2610 8. Operation STARTING ENGINE 5. Set the stop switch to the “-” position. Set the throttle trigger to the start position (1 → 2 → 3). WARNING Place the unit on a flat, firm place. The cutting head will start rotating upon the engine Keep the cutting head clear of everything around starts.
  • Page 11 PSZ2610 8. Operation 8. Allow the engine to warm up for a several minutes ADJUSTING IDLING SPEED before starting operation. NOTE 1. When restarting the engine immediately after stop- ping it, leave the choke open. 2. Overchoking can make the engine hard to start due to excess fuel.
  • Page 12 PSZ2610 8. Operation Adjusting Oil Flow Rate IMPORTANT The oil flow adjusting screw must be pressed in slightly WARNING in order to turn. Failure to do so could damage the pump Never fill the oil reservoir nor adjust the oiler with and screw.

  • Page 13: Maintenance

    PSZ2610 9. Maintenance Every Every Every Before System/components Procedure Note hours hours hours after after after fuel leaks, fuel spillage wipe out ✔ fuel tank, air filter, fuel filter inspect/clean replace, if necessary ✔ see adjusting idling replace carburetor idle speed adjuster ✔...
  • Page 14 PSZ2610 9. Maintenance SPARK ARRESTER OILING PORT • The muffler is equipped with a spark arrester to Dismount the guide bar and check the oiling port for prevent red hot carbon from flying out of the exhaust clogging. (MA1) outlet. Periodically inspect and clean as necessary with a wire brush in the repair specialty store.
  • Page 15 PSZ2610 9. Maintenance SPROCKET After every cutter has been set, check the depth gauge Check for extensive wear, and replace it when the teeth and file it to the proper level as illustrated. (MA7) are worn over 0.3 mm. 0.3 mm (1) Sprocket 0.25"...

  • Page 16: Storage

    → clogged with dust → consult with the repair specialty store When your unit seems to need further service, please consult with our ZENOAH service shop in your area. Limited warranty Should any failure occur on the product under normal operating WARRANTY OBLIGATION OF THE COMPANY.

Table of Contents