Related Manuals for Zenoah PSJ2300
Summary of Contents for Zenoah PSJ2300
- Page 1 OWNER’S MANUAL • Before using our products, please read this manual CAUTION carefully to understand the proper use of your unit. • Keep this manual handy. POLE SAW 长 柄 锯 PSJ2300 848-A57-93A0 (704)
-
Page 2: Table Of Contents
English SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail. -
Page 3: Parts Location
English 1. Parts location 1. Loop handle 2. Suspension point 3. Stop switch 4. Throttle cable 5. Throttle trigger 6. Shaft tube 7. Knob bolt 8. Starter knob 9. Fuel tank 10. Primer pump 11. Choke lever 12. Air cleaner cover 13. -
Page 4: Explanation Of Pictorials
English 2. Explanation of pictorials (1) Read owner's manual before operating this machine. (2) Wear head, eye and ear protection. (3) Warning/Attention (4) The unit been designed to provide protection from electric shock in the event of contact with overhead electric lines. -
Page 5: Safety Precautions
English 4. Safety precautions WARNING Approaching contacting electric power lines with Pole saw may cause serious injury or death from electrocution. Electricity can jump from one point to another by means of arcing or may be conducted through damp branches. Maintain a clearance of at least 15m between Pole saw and any electrical line carrying live... - Page 6 English 4. Safety precautions (6) Hatchet or saw (for removal of obstacles) 3. Do not wear loose clothing, jewelry, short trousers, sandals, or go barefoot. Do not wear anything which might be caught by a moving part of the unit. Secure hair so it is above shoulder length.
- Page 7 English 4. Safety precautions Repetitive Stress Injury(RSI) could occur. If you feel discomfort, redness and swelling of your fingers or any other part of your body, see a doctor before getting worse. 2. To avoid noise complaints, in general, operate product between 8a.m.
- Page 8 If it continues to rotate even after the throttle has been moved fully back, turn off the engine and take the unit to your authorized Zenoah servicing dealer for repair. ■ USING THE PRODUCT IMPORTANT Cut only materials recommended by the manufacturer.
- Page 9 ZENOAH products or products which have been certified by ZENOAH for use with the ZENOAH product. 中 文 4. 正确使用须知 3. 切勿以超过 60 度的角度操作修枝剪，...
- Page 10 ■ HANDLING FUEL 1. The engine of the ZENOAH product is designed to run on a mixed fuel which contains highly flammable gasoline. Never store cans of fuel or refill the tank of the...
- Page 11 English 4. Safety precautions and fix the unit by ropes. 4. Never transport the product over rough roads over long distances by vehicle without removing all fuel from the fuel tank. If doing so, fuel might leak from the tank during transport.
- Page 12 English 4. Safety precautions the manufacturer. WARNING • Make sure the chain and sprocket are correctly adjusted before operating the pruner (see page 14, 15 for adjustment procedures). Never attempt chain adjustment with the engine running! • Always make sure the cutting attachment is properly installed and firmly tightened before operation.
-
Page 13: Set Up
English 5. Set up ■ MOUNTING ENGINE (SE1) 1. Push the driveshaft housing toward the clutch housing and rotate it by hand to check that the driveshaft is engaged with the gears. 2. Insert the driveshaft housing into the clutch housing until it bottoms, and align the positioning holes on the both housings and install the screw. - Page 14 English 5. Set up ■ ATTACHING THE PRUNING MECHANISM (SE6) 1. Remove the cap on the end of the main pipe. 2. Remove the screw screwed into the end of the gear case. 3. Insert the end of the gear case into the main pipe.
- Page 15 SE10 SE11 English 5. Set up 3. Fit the chain tensioner nut into the lower hole of the guide bar, then install the chain cover, and fasten the mounting nut to finger tightness. (SE8) (SE9) (1) Hole (2) Moving direction (3) Chain tensioner nut 4.
-
Page 16: Fuel And Chain Oil
2-cycle engine oil into a mixing container in accordance with the following ratios and then shaking to mix well. Mixing ratios: When using Zenoah genuine 2-cycle oil (FC grade): 50:1 (100 ml of oil for every 5 liters of gasoline) When using commercially available... -
Page 17: Operation
English 7. Operation ■ STARTING ENGINE WARNING The cutting head will start rotating upon the engine starts. 1. Feed fuel and chain oil into their respective tanks and tighten the caps securely. (OP1) (1) Fuel (2) Chain oil 2. Rest the unit on a flat, firm place. Keep the cutting head off the ground and clear of surrounding objects as it will start rotating upon... - Page 18 English 7. Operation NOTE 1. When restarting the engine immediately after stopping it, leave the choke open. 2. Overchoking can make the engine hard to start due to excess fuel. When the engine failed to start after several attempts, open the choke and repeat pulling the rope, or remove the spark plug and dry ■...
- Page 19 .04 in (1~2mm) English 7. Operation check the oil level more frequently than at fuel tank refills. The guide bar and chain are lubricated automatically by a pump that operates whenever the chain rotates. The pump is set at the factory to deliver a minimum flow rate, but it can be adjusted in the field.
- Page 20 English 7. Operation ■ ADJUSTING IDLING SPEED (OP9) 1. When the engine tends stop frequently at idling mode, turn the adjusting screw clockwise. 2. When the cutting head keeps rotating after releasing the trigger, turn the adjusting screw counter- clockwise. (1) Idle adjusting screw NOTE •...
-
Page 21: Maintenance
8. Maintenance Maintenance, replacement, or repair of the emission control device and systems may be performed by any non-road engine repair establishment or individual. ■ MAINTENANCE CHART System/compornent fuel leaks, fuel spillage fuel tank, air filter, fuel filter idle adjusting screw spark plug cylinder fins, intake air cooling vent muffler, spark arrester,... - Page 22 English 8. Maintenace ■ OILING PORT Dismount the guide bar and check the oiling port for clogging. (MA1) (1) Oiling port ■ GUIDE BAR Remove sawdust in the bar groove and the oiling port. (MA2) (1) Groove (2) Oiling port (Type: Sprocket nose) Grease the nose sprocket from the feeding port on the tip of the bar.
- Page 23 English 8. Maintenace ■ SAW CHAIN WARNING It is very important for smooth and safe operation to keep the cutters always sharp. Your cutters need to be sharpened when: • Sawdust becomes powder-like. • You need extra force to saw in. •...
- Page 24 Clean the spark plug and check that the plug gap is in the correct range. For a replacement plug, use the correct type specified by ZENOAH. (MA11) • REPLACEMENT PLUG IS A NGK BPMR7A. IMPORTANT • Note that using any spark plug...
- Page 25 MA13 English 8. Maintenace grease nipples located on the gear case. (MA12) (1) Grease fitting ■ INTAKE AIR COOLING VENT WARNING • Never touch the cylinder, muffler, or spark plugs with your bare hands immediately after stopping the engine. The engine can become very hot when in operation, and doing so could result in severe burns.
- Page 26 MA14 English 8. Maintenace ■ PROCEDURES PERFORMED AFTER EVERY 100 HOURS OF USE 1. Remove the muffler, insert a screwdriver into the vent, and wipe away any carbon buildup. Wipe away any carbon buildup on the muffler exhaust vent and cylinder exhaust port at the same time.
-
Page 27: Troubleshooting Guide
9. Troubleshooting guide Case 1. Starting failure CHECK fuel tank fuel filter carburetor adjustment screw sparking (no spark) spark plug Case 2. Engine starts but does not keep running/Hard re-starting. CHECK fuel tank carburetor adjustment screw muffler,cylinder (exhaust port) air cleaner cylinder fin, fan cover When your unit seems to need further service, please consult with our service shop in your area. -
Page 28: Specifications
Type······················ Air-cooled 2-stroke gasoline Model ········································ Zenoah G23LS Displacement········································ 22.5cm Fuel ········································································· Mixture when using ZENOAH genuine oil (FC grade) ···············50:1 when using market oil (FB grade) ·······························25:1 Carburetor ····································· Walbro Diaphragm type Spark plug ····················································NGK BPMR7A Fuel tank capacity ························································0.6 Transmission ················...