USER MANUAL ENGLISH Thank you very much for choosing the iiyama LCD monitor. We recommend that you take a few minutes to read this comprehensive manual carefully before installing and switching on the monitor. Please keep this manual in a safe place for...
IIYAMA CORPORATION: Wijkermeerstraat 8, 2131 HA Hoofddorp, The Netherlands Model No. : PLT1521M We recommend recycling of used product. Please contact your dealer or iiyama service center. Recycle information is obtained via the Internet, using the address: http://www.iiyama.com You can access the Web page of different countries from there.
TABLE OF CONTENTS FOR YOUR SAFETY ................1 SAFETY PRECAUTIONS..............1 SPECIAL NOTES ON LCD MONITORS .........3 CUSTOMER SERVICE ..............3 CLEANING ..................3 BEFORE YOU OPERATE THE MONITOR ..........4 FEATURES..................4 CHECKING THE CONTENTS OF THE PACKAGE ......4 SPECIAL NOTES ON TOUCH PANEL..........5 WALL MOUNTING ................5 BUILT-IN EQUIPMENT ..............5 FITTING AND REMOVAL OF BASE ..........6 CONTROLS AND CONNECTORS..........7...
Do not put any solid objects or liquids such as water into the monitor. In case of an accident, unplug your monitor immediately and contact your dealer or iiyama service center. Using the monitor with any object inside may cause fi re, electric shock or damage.
Page 6
CAUTION INSTALLATION LOCATION Do not install the monitor where sudden temperature changes may occur, or in humid, dusty or smoky areas as it may cause fi re, electric shock or damage. You should also avoid areas where the sun shines directly on the monitor. DO NOT PLACE THE MONITOR IN A HAZARDOUS POSITION The monitor may topple and cause injury if not suitably located.
If you drop any materials or liquids such as water into the monitor when cleaning, WARNING unplug the power cable immediately and contact your dealer or iiyama service center. To protect the Touch screen surface, do not scratch or rub the screen with a hard NOTE object.
CHECKING THE CONTENTS OF THE PACKAGE The following accessories are included in your package. Check to see if they are enclosed with the monitor. If anything is missing or damaged, please contact your local iiyama dealer or regional iiyama offi ce.
SPECIAL NOTES ON TOUCH PANEL Permanent damage can occur if Sharp Edged, Pointed or Metal items are used to activate Touch. This could invalidate any remaining warranty. We recommend to use a plastic stylus (tip R0.8 or over) or fi nger. WALL MOUNTING W h e n y o u u s e w i t h t h e w a l l m o u n t i n g , i n Screw...
FITTING AND REMOVAL OF BASE Put the monitor on a stable surface. The monitor may cause injury or damage if it CAUTION falls or is dropped. Do not give a strong impact to the monitor. It may cause damage. ...
CONTROLS AND CONNECTORS <Front> <Back> Menu Button ( Up / Left / Auto Adjustment Button ( Down / Right Button ( Return / Exit Button ( Power Switch ( USB Connector VGA(D-sub) mini 15pin Connector Connector for AC Adapter ( : Direct current) Audio Connector Speakers...
An incorrect connection may cause serious damage to both the monitor and the computer. The cable supplied with the monitor is for a standard connector. If a special cable is required please contact your local iiyama dealer or regional iiyama offi ce.
Change to the desired signal timing listed on page 24: COMPLIANT TIMING. Windows XP/Vista/7/8/8.1/10 Plug & Play The iiyama LCD monitor complies with DDC2B of VESA standard. The Plug & Play function runs on Windows XP/Vista/7/8/8.1/10 by connecting the monitor to DDC2B compliant computer with the Signal Cable supplied.
ADJUSTING THE VIEWING ANGLE For optimal viewing it is recommended to look at the full face of the monitor. Hold the panel so that the monitor does not topple when you change the monitor’s angle. You are able to adjust the monitor’s angle up to 70 degrees upward, 10 degrees downward.
OPERATING THE MONITOR To create the best picture, your iiyama LCD monitor has been preset at the factory with the COMPLIANT TIMING shown on page 24. You are also able to adjust the picture by following the button operation shown below. For more detailed adjustments, see page 17 for SCREEN ADJUSTMENTS.
Page 16
Direct LOCK MODE: Pressing and holding of the Button for 3-4 seconds when the Menu is not displayed. * The OSD menu is not displayed when the OSD is locked. Pressing and holding of the Button for 3 - 4 seconds again when the Menu is not displayed. The following OSD menu is displayed.
ADJUSTMENT MENU CONTENTS PICTURE PICTURE Backlight Brightness Contrast Sharpness Adjustment Item Problem / Option Button to Press Too dark Backlight Too bright Too dark Brightness * Too bright Too dull Contrast Too intense 0 1 2 3 4 Sharpness You can change the picture quality from 0 to 4 (soft to sharp). Press the Button to change the picture quality in numerical order.
Page 18
DISPLAY DISPLAY Auto Adjustment H Position V Position Pixel Clock Phase Adjustment Item Problem / Option Button to Press Adjust H/V Position, Pixel Clock and Phase automatically. Auto Adjustment * Direct Too left H Position Too right Too low V Position Too high Too narrow Pixel Clock *...
Page 19
COLOR COLOR Color Temp User Preset Picture Mode Standard Adjustment Item Problem / Option Button to Press 9300 Bluish white Greenish white 7500 Yellowish white 6500 Color Temp 5500 Reddish white Too weak Green User Preset Too strong Blue Standard Typical Picture Mode Low Blue Light...
Page 20
OTHER OTHER Reset OSD Time OSD H Position OSD V Position English Language Adjustment Item Problem / Option Button to Press Reset Factory-preset data is restored. You can set the OSD display duration time OSD Time between 5 and 60 seconds. OSD is too left OSD H Position OSD is too right...
If the screen has a flicker or blur, or the picture does not fit in the display area after performing the Auto Adjust, manual adjustments are required. Both adjustments should be made by using the screen adjustment pattern (Test.bmp) obtained via the IIYAMA web site (http://www.iiyama. com).
Page 22
Press the Button. (Auto Adjustmnet) Adjust the image manually by following procedure below when the screen has a fl icker or blur, or the picture does not fi t in the display area after performing the Auto Adjust. Adjust the V Position so that the top and bottom of the picture frame will fi t to the display area.
Page 23
Adjust the Phase to correct horizontal wavy noise, fl icker or blur in the zebra pattern. In case the strong fl icker or blurs remain on a part of the screen, repeat steps NOTE because the Pixel Clock may not be adjusted correctly. If the fl icker or blurs still remain, set the refresh rate of computer to low (60Hz) and repeat steps from again.
POWER MANAGEMENT FEATURE The power management feature of this product complies with power saving requirement of VESA DPMS. When activated, it automatically reduces unnecessary power consumption of the monitor when your computer is not in use. To use the feature, the monitor needs to be connected to a VESA DPMS compliant computer. There is a power management step the monitor takes as described below.
MONITOR or if the problem persists. 3. If you are experiencing a problem which is not described below or you cannot correct the problem, discontinue using the monitor and contact your dealer or iiyama service center for further assistance. Problem...
RECYCLING INFORMATION For better environment protection please don't dispose your monitor. Please visit our web site: www.iiyama.com/recycle for monitor recycling. 22 RECYCLING INFORMATION...
APPENDIX Design and specifi cations are subject to change without prior notice. SPECIFICATIONS Technology Projected capacitive 10pt touch Touch Screen Light transmission 88% Communication USB serial transfer system Size Category 15" Driving system a-Si TFT Active Matrix Panel Size Diagonal: 15" (38cm) Pixel pitch 0.297mm H ×...
Need help?
Do you have a question about the ProLite T1521MSC and is the answer not in the manual?
Questions and answers