Page 1
ENGLISH Thank you very much for choosing the iiyama LCD monitor. We recommend that you take a few minutes to read this comprehensive manual carefully before installing and switching on the monitor. Please keep this manual in a safe place for your future reference.
Page 2
Downloaded from ManualMonitor.com Manuals...
IIYAMA CORPORATION: Wijkermeerstraat 8, 2131 HA Hoofddorp, The Netherlands We recommend recycling of used product. Please contact your dealer or iiyama service center. Recycle information is obtained via the Internet, using the address: http://www.iiyama.com...
Power Switch for hours. Contact your dealer or iiyama service center for the backlight replacement when the screen is dark, fl ickering or not lighting up. Never attempt to replace it by yourself.
CHECKING THE CONTENTS OF THE PACKAGE The following accessories are included in your package. Check to see if they are enclosed with the monitor. If anything is missing or damaged, please contact your local iiyama dealer or regional iiyama offi ce.
An incorrect connection may cause serious damage to both the monitor and the computer. The cable supplied with the monitor is for a standard 15 pin D-Sub connector. If a special cable is required please contact your local iiyama dealer or regional iiyama offi ce.
Change to the desired signal timing listed on page 28: COMPLIANT TIMING. Windows 95/98/2000/Me/XP/Vista/7 Plug & Play The iiyama LCD monitor complies with DDC2B of VESA standard. The Plug & Play function runs on Windows 95/98/2000/Me/XP/Vista/7 by connecting the monitor to DDC2B compliant computer with the Signal Cable supplied.
Page 13
Downloaded from ManualMonitor.com Manuals...
ADJUSTMENT MENU CONTENTS CO NT R AS T BR I G HT NE S S 1 2 8 0 x1 0 2 4 FH : 6 3 K Hz F V: 59 . 9Hz Adjustment Item Problem / Option Button to Press Too dull CONTRAST Too intense...
AU TO A D JU ST Only Analog Input H- PO SIT ION V-P OSIT IO N H - SIZ E F IN E Adjustment Item Problem / Option Button to Press Direct Adjust H/V-POSITION, H-SIZE and FINE automatically. AUTO ADJUST * Too left H-POSITION Too right...
Page 16
OS D H - P OS I T I ON O S D V- P OS I TI ON OS D TI M E OU T RE S E T I N P UT S EL EC T Adjustment Item Problem / Option Button to Press OSD is too left...
Page 17
9300 6500 5500 GREEN 7500 BLUE USER Adjustment Item Problem / Option Button to Press 9300 Bluish white 6500 Reddish white 5500 Greenish white COLOR TEMP. Yellowish white 7500 Too weak GREEN User Too strong BLUE VOLUME MUTE Adjustment Item Problem / Option Button to Press Too soft...
If the screen has a fl icker or blur, or the picture does not fi t in the display area after performing the Auto Adjust, manual adjustments are required. Both adjustments should be made by using the screen adjustment pattern (Test.bmp) obtained via the IIYAMA web site (http://www.iiyama.com). Adjust the image by following the procedure below to get the desired picture.
Page 19
C Press the AUTO Button. (AUTO ADJUST) D Adjust the image manually by following procedure below when the screen has a fl icker or blur, or the picture does not fi t in the display area after performing the Auto Adjust. E Adjust the V-POSITION so that the top and bottom of the picture frame will fit to the display area.
Page 20
Downloaded from ManualMonitor.com Manuals...
POWER 2W or 3W* 100% CONSUMPTION * ProLite T1531SR / ProLite T1731SR / ProLite T1931SR / ProLite T1532SR:2W ProLite T1531SAW / ProLite T1731SAW / ProLite T1931SAW:3W NOTE Even when using the power management mode, the monitor consumes electricity. Turn off the Power Switch whenever the monitor is not in use, during the night and weekends, to avoid unnecessary power consumption.
Page 22
Downloaded from ManualMonitor.com Manuals...
APPENDIX SPECIFICATIONS : ProLite T1531SR Touch Technology Resistive-Film Screen Anti-glare treatment Surface processing Light transmission Communication USB serial transfer or RS-232C serial transfer system Size Category 15" LCD Panel Driving system a-Si TFT Active Matrix Size Diagonal: 15" (38cm) Pixel pitch 0.297mm H ×...
SPECIFICATIONS : ProLite T1531SAW Touch Technology Surface acoustic wave Screen Anti-glare treatment Surface processing Light transmission Communication USB serial transfer or RS-232C serial transfer system Size Category 15" LCD Panel Driving system a-Si TFT Active Matrix Size Diagonal: 15" (38cm) Pixel pitch 0.297mm H ×...
SPECIFICATIONS : ProLite T1532SR Touch Technology Resistive-Film Screen Anti-glare treatment Surface processing Light transmission Communication USB serial transfer or RS-232C serial transfer system Size Category 15" LCD Panel Driving system a-Si TFT Active Matrix Size Diagonal: 15" (38cm) Pixel pitch 0.297mm H ×...
SPECIFICATIONS : ProLite T1731SR Touch Technology Resistive-Film Screen Anti-glare treatment Surface processing Light transmission Communication USB serial transfer or RS-232C serial transfer system Size Category 17" LCD Panel Driving system a-Si TFT Active Matrix Size Diagonal: 17" (43cm) Pixel pitch 0.264mm H ×...
SPECIFICATIONS : ProLite T1731SAW Touch Technology Surface acoustic wave Screen Anti-glare treatment Surface processing Light transmission Communication USB serial transfer or RS-232C serial transfer system Size Category 17" LCD Panel Driving system a-Si TFT Active Matrix Size Diagonal: 17" (43cm) Pixel pitch 0.264mm H ×...
SPECIFICATIONS : ProLite T1931SR Touch Technology Resistive-Film Screen Anti-glare treatment Surface processing Light transmission Communication USB serial transfer or RS-232C serial transfer system Size Category 19" LCD Panel Driving system a-Si TFT Active Matrix Size Diagonal: 19" (48cm) Pixel pitch 0.294mm H ×...
SPECIFICATIONS : ProLite T1931SAW Touch Surface acoustic wave Technology Screen Anti-glare treatment Surface processing Light transmission Communication USB serial transfer or RS-232C serial transfer system Size Category 19" LCD Panel Driving system a-Si TFT Active Matrix Size Diagonal: 19" (48cm) Pixel pitch 0.294mm H ×...