Iiyama ProLite T1531SR User Manual
Hide thumbs
Also See for ProLite T1531SR:
- User manual (36 pages) ,
- Specification (1 page) ,
- User manual (33 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Iiyama ProLite T1531SR
Summary of Contents for Iiyama ProLite T1531SR
-
Page 1: User Manual
USER MANUAL ENGLISH Thank you very much for choosing the iiyama LCD monitor. We recommend that you take a few minutes to read this comprehensive manual carefully before installing and switching on the monitor. Please keep this manual in a safe place for... -
Page 3: Ce Marking Declaration Of Conformity
IIYAMA CORPORATION: Breguetlaan 8, 1438BC Oude Meer The Netherlands We recommend recycling of used product. Please contact your dealer or iiyama service center. Recycle information is obtained via the Internet, using the address: http://www.iiyama.com... -
Page 4: Table Of Contents
SPECIFICATIONS : ProLite T1931SR ............25 SPECIFICATIONS : ProLite T1931SAW ............26 DIMENSIONS : ProLite T1531SR / ProLite T1531SAW / ProLite T1532SR ... 27 DIMENSIONS : ProLite T1731SR / ProLite T1731SAW ......... 27 DIMENSIONS : ProLite T1931SR / ProLite T1931SAW ........ 27... -
Page 5: For Your Safety
STOP OPERATING THE MONITOR WHEN YOU SENSE TROUBLE If you notice any abnormal phenomena such as smoke, strange sounds or fumes, unplug the monitor and contact your dealer or iiyama service center immediately. Further use may be dangerous and can cause fi re or electric shock. - Page 6 CAUTION INSTALLATION LOCATION Do not install the monitor where sudden temperature changes may occur, or in humid, dusty or smoky areas as it may cause fi re, electric shock or damage. You should also avoid areas where the sun shines directly on the monitor. DO NOT PLACE THE MONITOR IN A HAZARDOUS POSITION The monitor may topple and cause injury if not suitably located.
-
Page 7: Special Notes On Lcd Monitors
Power Switch for hours. Contact your dealer or iiyama service center for the backlight replacement when the screen is dark, fl ickering or not lighting up. Never attempt to replace it by yourself. CUSTOMER SERVICE ... -
Page 8: Before You Operate The Monitor
ProLite T1731SR / ProLite T1731SAW / ProLite T1931SR / ProLite T1931SAW High Contrast 500:1 (Typical: with Touch panel) / Brightness 200cd/m (Typical: with Touch panel) : ProLite T1531SR / ProLite T1532SR High Contrast 500:1 (Typical: with Touch panel) / Brightness 230cd/m (Typical: with Touch panel) : ProLit T1531SAW ... -
Page 9: Checking The Contents Of The Package
CHECKING THE CONTENTS OF THE PACKAGE The following accessories are included in your package. Check to see if they are enclosed with the monitor. If anything is missing or damaged, please contact your local iiyama dealer or regional iiyama offi ce. Power Cable* ... -
Page 10: Controls And Connectors
CONTROLS AND CONNECTORS <Front> <Back> Menu Button ( Scroll Up / Brightness Button ( Scroll Down / Mute Button ( Select / Auto Button ( Power Switch ( Keyhole for Security Lock NOTE You can fasten a security lock and cable to prevent the monitor from being removed without your permission. -
Page 11: Connecting Your Monitor
The cable supplied with the monitor is for a standard 15 pin D-Sub connector. If a special cable is required please contact your local iiyama dealer or regional iiyama offi ce. For connection to Macintosh computers, contact your local iiyama dealer or regional iiyama offi... -
Page 12: Computer Setting
Change to the desired signal timing listed on page 28: COMPLIANT TIMING. Windows 95/98/2000/Me/XP/Vista/7 Plug & Play The iiyama LCD monitor complies with DDC2B of VESA standard. The Plug & Play function runs on Windows 95/98/2000/Me/XP/Vista/7 by connecting the monitor to DDC2B compliant computer with the Signal Cable supplied. -
Page 13: Operating The Monitor
OPERATING THE MONITOR To create the best picture, your iiyama LCD monitor has been preset at the factory with the COMPLIANT TIMING shown on page 28. You are also able to adjust the picture by following the button operation shown below. For more detailed adjustments, see page 14 for SCREEN ADJUSTMENTS. -
Page 14: Adjustment Menu Contents
ADJUSTMENT MENU CONTENTS CONTRA ST BRIGHT NESS 1 28 0x 10 24 F H : 6 3K H z F V: 59 .9 H z Adjustment Item Problem / Option Button to Press Too dull CONTRAST Too intense Too dark Direct BRIGHTNESS * Too bright... - Page 15 A U TO A D J U S T Only Analog Input H - P O S I T I O N V- P O S I T I O N H- S I Z E F I N E Adjustment Item Problem / Option Button to Press...
- Page 16 O S D H - PO SI TI ON O SD V- PO SI TI ON OS D TIME OU T R ES ET IN PU T S ELE C T Adjustment Item Problem / Option Button to Press OSD is too left OSD H-POSITION OSD is too right OSD is too low...
- Page 17 9300 6500 5500 GREEN 7500 BLUE USER Adjustment Item Problem / Option Button to Press 9300 Bluish white 6500 Reddish white Greenish white 5500 COLOR TEMP. 7500 Yellowish white Too weak GREEN USER Too strong BLUE VOLUME MUTE Adjustment Item Problem / Option Button to Press Too soft...
-
Page 18: Screen Adjustments
If the screen has a fl icker or blur, or the picture does not fi t in the display area after performing the Auto Adjust, manual adjustments are required. Both adjustments should be made by using the screen adjustment pattern (Test.bmp) obtained via the IIYAMA web site (http://www.iiyama.com). Adjust the image by following the procedure below to get the desired picture. - Page 19 C Press the Auto Button. (AUTO ADJUST) D Adjust the image manually by following procedure below when the screen has a fl icker or blur, or the picture does not fi t in the display area after performing the Auto Adjust. E Adjust the V-POSITION so that the top and bottom of the picture frame will fi...
- Page 20 G Adjust the FINE to correct horizontal wavy noise, fl icker or blur in the zebra pattern. NOTE In case the strong fl icker or blurs remain on a part of the screen, repeat steps F and NOTE G because the H-SIZE may not be adjusted correctly.
-
Page 21: Power Management Feature
POWER 2W or 3W* 100% CONSUMPTION * ProLite T1531SR / ProLite T1731SR / ProLite T1931SR / ProLite T1532SR 2W ProLite T1531SAW / ProLite T1731SAW / ProLite T1931SAW 3W NOTE Even when using the power management mode, the monitor consumes electricity. Turn off the Power Switch whenever the monitor is not in use, during the night and weekends, to avoid unnecessary power consumption. -
Page 22: Trouble Shooting
MONITOR or if the problem persists. If you are experiencing a problem which is not described below or you cannot correct the problem, discontinue using the monitor and contact your dealer or iiyama service center for further assistance. Problem Check The picture does ... -
Page 23: Recycling Information
RECYCLING INFORMATION For better environment protection please don't dispose your monitor. Please visit our web site: www.iiyama.com/recycle for monitor recycling. RECYCLING INFORMATION... -
Page 24: Appendix
APPENDIX SPECIFICATIONS : ProLite T1531SR Touch Technology Resistive-Film Screen Anti-glare treatment Surface processing Light transmission Communication USB serial transfer or RS-232C serial transfer system Size Category 15" LCD Panel Driving system a-Si TFT Active Matrix Size Diagonal: 15" (38cm) Pixel pitch 0.297mm H ×... -
Page 25: Specifications : Prolite T1531Saw
SPECIFICATIONS : ProLite T1531SAW Touch Technology Surface acoustic wave Screen Anti-glare treatment Surface processing Light transmission Communication USB serial transfer or RS-232C serial transfer system Size Category 15" LCD Panel Driving system a-Si TFT Active Matrix Size Diagonal: 15" (38cm) Pixel pitch 0.297mm H ×... -
Page 26: Specifications : Prolite T1532Sr
SPECIFICATIONS : ProLite T1532SR Touch Technology Resistive-Film Screen Anti-glare treatment Surface processing Light transmission Communication USB serial transfer or RS-232C serial transfer system Size Category 15" LCD Panel Driving system a-Si TFT Active Matrix Size Diagonal: 15" (38cm) Pixel pitch 0.297mm H ×... -
Page 27: Specifications : Prolite T1731Sr
SPECIFICATIONS : ProLite T1731SR Touch Technology Resistive-Film Screen Anti-glare treatment Surface processing Light transmission Communication USB serial transfer or RS-232C serial transfer system Size Category 17" LCD Panel Driving system a-Si TFT Active Matrix Size Diagonal: 17" (43cm) Pixel pitch 0.264mm H ×... -
Page 28: Specifications : Prolite T1731Saw
SPECIFICATIONS : ProLite T1731SAW Touch Technology Surface acoustic wave Screen Anti-glare treatment Surface processing Light transmission Communication USB serial transfer or RS-232C serial transfer system Size Category 17" LCD Panel Driving system a-Si TFT Active Matrix Size Diagonal: 17" (43cm) Pixel pitch 0.264mm H ×... -
Page 29: Specifications : Prolite T1931Sr
SPECIFICATIONS : ProLite T1931SR Touch Technology Resistive-Film Screen Anti-glare treatment Surface processing Light transmission Communication USB serial transfer or RS-232C serial transfer system Size Category 19" LCD Panel Driving system a-Si TFT Active Matrix Size Diagonal: 19" (48cm) Pixel pitch 0.294mm H ×... -
Page 30: Specifications : Prolite T1931Saw
SPECIFICATIONS : ProLite T1931SAW Touch Surface acoustic wave Technology Screen Anti-glare treatment Surface processing Light transmission Communication USB serial transfer or RS-232C serial transfer system Size Category 19" LCD Panel Driving system a-Si TFT Active Matrix Size Diagonal: 19" (48cm) Pixel pitch 0.294mm H ×... -
Page 31: Dimensions : Prolite T1531Sr / Prolite T1531Saw / Prolite T1532Sr
DIMENSIONS : ProLite T1531SR / ProLite T1531SAW / ProLite T1532SR 351.0mm/13.8" 59.0mm/2.3" 306.0mm/12.0" 222.5mm/8.8" DIMENSIONS : ProLite T1731SR / ProLite T1731SAW 387.0mm/15.2" 59.0mm/2.3" 340.0mm/13.4" 222.5mm/8.8" DIMENSIONS : ProLite T1931SR / ProLite T1931SAW 432.0mm/17.0" 59.0mm/2.3" 378.0mm/14.9" 249.5mm/9.8" APPENDIX... -
Page 32: Compliant Timing
50.000MHz 48.077kHz 72.188Hz 65.000MHz 48.363kHz 60.004Hz 1024 × 768 56.476kHz 70.069Hz 75.000MHz 60.023kHz 75.029Hz 78.750MHz 63.981kHz 60.020Hz 108.000MHz SXGA 1280 × 1024 79.976kHz 75.025Hz 135.000MHz NOTE * Not compliant to ProLite T1531SR / ProLite T1531SAW / ProLite T1532SR. APPENDIX M059C02...
Need help?
Do you have a question about the ProLite T1531SR and is the answer not in the manual?
Questions and answers