Choosing The Correct Intensity Level; Device Information; Pro Control 2 Handheld Device Specifications; Pro Control 2 Battery Replacement Instructions - Garmin PRO Control 2 HH Owner's Manual

Mode Top Key Middle Key
TVM Tone Vibration
VCM Vibration Continuous
(high)
TCM Tone Continuous
(high)
CMM Continuous Momentary
(high) (high)
MCC Momentary Continuous
(high) (high)
Selecting a Training Mode
You can select a different training mode for each dog collar
device.
1
Select a dog collar device
2
Select RAPID LAUNCH to toggle through the available
training modes.

Choosing the Correct Intensity Level

1
Set the intensity to the lowest level
Level).
2 Press a training key.
3 Observe the dog for a reaction, such as a head shake, neck
movement, or just a change in expression.
Sometimes dogs will vocalize due to the surprise of the
electrical stimulation. If the dog vocalizes more than once,
the intensity level is too high for beginning training.
4
If there is no reaction, increase the intensity level by one level
until the dog has a slight but recognizable reaction to the
stimulation.
The intensity level that causes a slight but recognizable reaction
is your dog's baseline level for beginning collar training. You do
not need to, and should not, apply this intensity selection test
again.
After you begin training, the dog's performance guides your
intensity selection. As the dog advances in training, you may
need to change the level depending upon the training situation.
Changing the Intensity Level
You can select a different intensity level for each dog collar
device.
1
Select a dog collar device
2
Select or to increase or decrease the intensity level.
The numerical intensity level appears on the LCD display.
TIP: You can hold or
quickly.

Device Information

PRO Control 2 Handheld Device
Specifications
Battery type
Operating temperature range
Charging temperature range
Storage temperature range
Water rating
*The device withstands incidental exposure to water of up to 1 m
for up to 30 min. For more information, go to
/waterrating.
4
Bottom Key Description
Momentary Beginning trainer,
(low) sensitive dog, or
minor corrections
Momentary All-around training
(high)
Momentary All-around training
(high)
Momentary Advanced
(low) training, popular
for bird-dog
training
Continuous Advanced
(low) training, popular
for obedience
training
(Selecting a Dog Collar Device).
(Changing the Intensity
(Selecting a Dog Collar Device).
to cycle through intensity levels
Rechargeable, replaceable lithium-ion
From -4° to 158°F (from -20° to 70°C)
From 32° to 104°F (from 0° to 40°C)
From -4° to 122°F (from -20° to 50°C)
IEC 60529 IPX7*
www.garmin.com
PRO Control 2 Battery Replacement
Instructions
This product contains a lithium-ion battery. To prevent the
possibility of personal injury or product damage caused by
battery exposure to extreme heat, store the device out of direct
sunlight.
Do not use a sharp object to remove batteries.
Contact your local waste disposal department to properly
recycle the batteries.
PRO Control 2 Handheld Device Components
Security screws
Back plate
Battery
Battery connector
Gasket
Replacing the PRO Control 2 Handheld Device Battery
Before you replace the battery, you must remove all dirt, water,
and debris from the device. You also need the security
screwdriver included with the new battery.
You can purchase a replacement battery at
http://buy.garmin.com. You should use only an official Garmin
replacement part.
1
Remove the six security screws from the back of the device.
2
Lift up the back plate.
3
Grip the battery connector wires close to the connector, and
pull the connector parallel to the circuit board to disconnect
the battery connector from the device.
4
Remove the old battery from the back plate, noting the
orientation of the battery.
The battery fits tightly. It may be necessary to pry the battery
out of the back plate using a non-sharp, non-metal object.
5
Install the new battery into the back plate with the label side
up, using the same orientation as the old battery.
6
With the new battery, connect the battery connector to the
device.
When properly installed, the connector plug snaps into the
port.
7
Verify the gasket is not damaged and is completely seated in
the groove.
8 Hold the back plate and the device firmly together, and
replace all six security screws without tightening.
9 Verify the back plate and the device are aligned with no gaps.
10
Tighten the screws evenly.
WARNING
CAUTION
Device Information
®