Version 1.10; Maintenance Items; Version 1.60; Option Slot Cards - Tascam DM-3200 Release Notes

Version 1.10

• V 1.10 of the DM-3200 Operating system provides DAW
remote control functionality using the
Layer. Support has been added for DigiDesign Pro
Tools, Cakewalk SONAR, MOTU Digital Performer,
Steinberg's Nuendo & Cubase and Apple Logic Pro.
Each of these has a dedicated manual in PDF format.
Please refer to the PDF specific to your DAW applica-
tion for details.
• It is now possible to execute a project store directly from
the front panel. Press Control + Library Store together
to operate this shortcut.

Maintenance Items

This section describes the Maintenance items for each revision of the DM-3200 software.

Version 1.60

Option Slot Cards

ª
At 88.2 kHz or 96 kHz sampling rates, some master
•
clock settings would result in audio transferred from an
IF-TD/DM option card to have reversed Odd and Even
channels. This problem has been fixed.
With an IF-FW/DM MKII card in slot 1 and an IF-SM/
•
DM card in Slot 3, the mixer would not be able to boot
correctly. This problem has been fixed.
With an IF-SM/DM installed, pressing the
•
key produced a click noise in the output. This has
SEL
been fixed.
• With the IF-SM/DM, and Bass Management set to
ON, changing the LPF setting of the Bass Management
Section would result in noise in the SubWoofer output
channel. This problem has been fixed.
Noise resulting from changing the Monitor level of the
•
IF-SM/DM has been removed.
With an IF-SM/DM installed, the front panel
•
key normally toggles the IF-SM/DM Downmix function
On or Off. A problem where this function did not occur
correctly has been fixed.
When the output gain of the IF-SM/DM was set to a
•
large value, activating a Buss Mute resulted in the Mute
occurring as a fade over a noticeable amount of time.
This problem has been fixed.

Remote Control

ª
If the Internal Timecode Generator (MTC Generate)
•
was started and then deleted from the Control List, the
MTC Timecode would not stop. This problem has been
fixed.
The mixer is now better able to lock to incoming MTC
•
Timecode that has Jitter.
• At the 30NDF frame rate, the MTC output could occa-
sionally produce incorrect Timecode values. This has
been fixed.
The operation of the Shuttle and
•
MMC protocol has been improved.
DM-3200 Release Notes
REMOTE Fader
MONITOR
MONO
controls using the
JOG
• It is now possible to change all the Program Change
Library Number assignments to "--" using the MIDI
Program Change Batch Setup.
When using the internal MTC Generator, pressing
•
STOP + REW on the front panel will jump to the start Time.
On the Meter/Fader screen,
•
Meter layer for easy access.
A problem where Timecode Locations were incorrectly
•
stored has been fixed.

When connected to TMCompanion

ª
With the TMCompanion Meter screen open, rebooting
•
the computer would result in the DM-4800 becoming
unresponsive. This problem has been fixed.

Monitor Section

ª
• Feedback noise that was created when the
key was pressed has been fixed.
Click noise that occurred when the
•
keys were pressed has been fixed.
MONITOR SEL

Project

ª
When a project is loaded, the front panel Encoder Mode
•
LED would not reflect the setting from the saved proj-
ect. This problem has been fixed.
• When Shutting Down the mixer, even if the Current
Project was not Protected, the following popup message
would sometimes be displayed.
" Current Project is protected.
" Can't STORE current project.
This problem has been fixed.

Operation

ª
When changing between an FS of 48kHz and 96kHz, the
EQ settings were not correctly restored. This problem has
been fixed.

Factory Default Settings.

ª
The Factory Default Setting for FADER SENSITIVITY
has been changed from 3.3kHz to 2.0kHz.
TASCAM DM-3200 Release Notes
POD 1 now controls the
TO SLATE
TO SLATE or
"
"
17