Page 1
18V CORDLESS COMBO PACK 93816 ASSEMBLY AND OPERATING INSTRUCTIONS Due to continuing improvements, actual product may differ slightly from the product described herein. ® 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com TO PREVENT SERIOUS INJURY, READ AND UNDERSTAND ALL WARNINGS AND INSTRUCTIONS BEFORE USE.
Freight Tools at the number shown on the cover of this manual as soon as possible. Note: Before first use, the Batteries (47) will require charging. The first charge requires 8 hours charge time for each battery. See charging instructions on page 10. SKU 93816 For technical questions, please call 1-800-444-3353. Page 2...
Do not operate power tools in explosive atmospheres, such as in the pres- ence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes. SKU 93816 For technical questions, please call 1-800-444-3353. Page 3...
Page 4
Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts. SKU 93816 For technical questions, please call 1-800-444-3353. Page 4...
Page 5
Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool’s operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools. SKU 93816 For technical questions, please call 1-800-444-3353. Page 5...
Page 6
The green wire in the cord must be the only wire connected to the tool’s grounding system and must never be attached to an electrically “live” terminal. (See Figure A.) SKU 93816 For technical questions, please call 1-800-444-3353. Page 6...
Page 7
The smaller the gauge number of the wire, the greater the capacity of the cord. For example, a 14 gauge cord can carry a higher current than a 16 gauge cord. (See Figure C.) SKU 93816 For technical questions, please call 1-800-444-3353. Page 7...
Page 8
Always replace a damaged extension cord or have it repaired by a qualified electri- cian before using it. Protect your extension cords from sharp objects, excessive heat, and damp or wet areas. Symbology SKU 93816 For technical questions, please call 1-800-444-3353. Page 8...
The operator must understand that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. SKU 93816 For technical questions, please call 1-800-444-3353. Page 9...
Then, disconnect the Charger from the Battery. * The Batteries (47) require an initial charge time of 8 hours each; do not recharge the Batteries more than 5 hours after this initial charging. SKU 93816 For technical questions, please call 1-800-444-3353. Page 10...
D. Then, firmly retighten the Cap Screw (29) to secure the Saw Blade (23) in place. E. Gently pull on the Blade (23) with a gloved hand to ensure it is held properly. SKU 93816 For technical questions, please call 1-800-444-3353.
Reflector, push and hold it in, and turn it counterclockwise. E. Put the Reflector (5a) back in place. Reattach the Lens (6a) and Holding Ring (4a). SKU 93816 For technical questions, please call 1-800-444-3353. Page 12...
Chuck (27b) counterclockwise. Insert the shank of a drill bit all the way into the Chuck. While holding the Chuck Sleeve in place, turn the Chuck clockwise to lock the drill bit in place. SKU 93816 For technical questions, please call 1-800-444-3353. Page 13...
Page 14
To turn on the Drill, squeeze the Trigger (18b). NOTE: Always grip the Drill firmly with both hands when the tool is running. Release the Trigger (18b) to stop the Drill. Then, remove the Battery (47) and drill bit from the Drill. SKU 93816 For technical questions, please call 1-800-444-3353. Page 14...
The Fence (39c) helps you cut multiple times at roughly the same distance. To Adjust the Fence (39c): A. Loosen the Fence Knob (42c). B. Move the Fence as desired. C. Retighten the Fence Knob securely. SKU 93816 For technical questions, please call 1-800-444-3353. Page 15...
Page 16
Adjust the depth of cut to the shallowest setting. Insert the fully charged Battery (47) in the Circular Saw’s handle, and make sure it snaps into place on the handle. The depth of cut can now be adjusted to the desired setting for use. SKU 93816 For technical questions, please call 1-800-444-3353. Page 16...
Page 17
Release the Trigger (4c) and Safety (21c) once the cut is completed. As a safety measure, remove the Battery (47) when work is completed. SKU 93816 For technical questions, please call 1-800-444-3353. Page 17...
MENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as original or replacement parts. SKU 93816 For technical questions, please call 1-800-444-3353. Page 18...
Need help?
Do you have a question about the 93816 and is the answer not in the manual?
Questions and answers