Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Related Manuals for Sony IPELA SNC-VM772R
Summary of Contents for Sony IPELA SNC-VM772R
-
Page 1: Network Camera
C-200-100-11 (1) Network Camera Installation Manual Before operating the unit, please read this manual thoroughly and retain it for future reference. SNC-VM772R © 2015 Sony Corporation... -
Page 2: Table Of Contents
About the Manuals Table of Contents Read This First (supplied) About the Manuals ............ 2 Location and Function of Part ......... 3 The Read This First manual describes the URL of the Preparations .............. 7 download site and the QR code. Be sure to read it. Change connections and cable wiring .... -
Page 3: Location And Function Of Part
• MIC terminal (minijack, monaural) Location and Function of Connect a commercially available microphone. This jack supports pluginpower microphones. Part B I/O (Input/Output) cable This cable is provided with two sensor inputs and two alarm outputs. Side The wires of the cable control the following signals. Color of wire Name Sensor In 1+... -
Page 4: Camera Head
f Side conduit hole ( inches NPT or M27 (2.0 mm ( inches)-pitched, hole diameter ø27 mm (1 inches))) Connect a pipe to this hole. There is a conduit hole on the side of the camera unit. The conduit hole cover is installed in the side conduit hole at the factory. -
Page 5: Camera Unit
Infrared LED a Connector dedicated to WLAN (Wireless LAN Note terminal) Attach a separately sold Sony product; USB Wireless LAN For inquiries regarding verified SD memory cards, contact Module IFU-WLM3 (hereafter WLAN module). your authorized Sony dealer. Use the module to view the angle adjustment when d SD MOUNT indicator installing the camera. -
Page 6: Hdmi Connector
l NETWORK indicator (Green/Orange) Notes The indicator lights up or flashes when the camera is connected to the network. • To prevent the HDMI cable disconnecting from the The indicator is off when the camera is not connected to camera (either by its own weight or an external force), it the network. -
Page 7: Preparations
• Waterproof the connection part between the cable and Preparations the sealing rubber. c) If you use the side conduit hole Change connections and cable 1 Remove the side conduit hole cover. wiring The supplied LAN cable is connected to the camera at the factory. -
Page 8: Installation
Mounting screws Installation The supplied bracket is provided with eight ø4.5 mm inches) mounting holes. Install the bracket on a ceiling or wall by tightening screws through four mounting holes (83.5 mm (3 inches) or 85.7 mm (3 inches)- WARNING pitched). -
Page 9: Installing The Camera
Remove the dome casing. Installing the Camera 1 Loosen the screws with the wrench (supplied). 2 Pull up and remove the dome casing. When the screw catches on the screw hole, pull up the screw. Wrench Install the supplied bracket on the ceiling or wall. “O”... -
Page 10: Installing The Camera (If You Use A Commercially Available Lan Cable)
Attach the camera unit to the bracket with the camera Perform the steps 5 to 6 of “Installing the Camera” unit mounting screws (four screws). (page 9). Tighten the four mounting screws attached to the unit, and Note fix the camera unit to the bracket. When using a flanged pipe or cable gland, refer to “Important precautions”... -
Page 11: Attaching The Dome Casing
Adjust the camera to turn the lens in the desired Attaching the Dome Casing direction. (Pan/Tilt/Rotation) Adjust the angle of view or focus while viewing the Fix the dome casing and the camera unit images, and decide the range in which the camera will Align four screw holes on the dome casing with those on shoot. -
Page 12: Important Precautions
Despite the fact that this unit is rated IP66, this section Important precautions includes important precautions to prevent any malfunction caused by condensation and/or water ingress. Read the precautions below thoroughly before installing the unit. • Make sure to install the camera unit so that the surface of the connection cables (including connectors) does not water. -
Page 13: Connection
Connecting to the power supply Connection equipment pursuant to IEEE802.3af The power supply equipment pursuant to IEEE802.3af Connecting to the Network supplies the power through a commercially available network cable. For details, refer to the Instruction Manual of the equipment. Connect the LAN port of the camera to a router or hub in the network using a commercially available network cable (not supplied). -
Page 14: Assigning The Ip Address
Assign an IP address to the camera. Assign an IP address to the camera using the installed SNC toolbox. For details, see “Using SNC toolbox” - “Assign an IP address” in the Application Guide. SNC toolbox stands for Sony Network Camera toolbox. -
Page 15: Specifications
Specifications SNC-VM772R Camera Image Sensor 1.0-type progressive scan Exmor R CMOS sensor Number of Effective Pixels Approx. 20 Megapixels Sync System Internal synchronization Minimum Illumination (30 IRE) Color: 0.06 lx (F1.8, 1/30 s) B/W: 0 lx (IR LED On, F1.8, 1/30 s) Horizontal Viewing Angle 70.7°... - Page 16 It may appear flawless, but the components may have deteriorated over time, which may cause a malfunction or accident. For details, please consult the store of purchase or an authorized Sony dealer. Caution The Network Camera is to be connected only to PoE networks without routing to the outside plant.