Maytag 120 V Installation Instructions Manual page 11

CONTROL SET-UP PROCEDURES
IMPORTANT: Read all instructions before operating.
The lower fabric setting key pads and the digital display are used
to set up the controls. The display can contain 4 numbers and/or
letters and a decimal point. These are used to indicate the set-up
codes and related code values available for use in programming
the washer.
How to use the key pads to program the controls
1. The LOWER LEFT key pad is used to adjust the values
associated with set-up codes. Pressing the key pad will
increment the value.
Rapid adjustment is possible by holding the key pad down.
2. The LOWER MIDDLE key pad will advance you through the
set-up codes. Pressing the key pad will advance you to the
next available set-up code. Holding the key pad down will
automatically advance through the set-up codes at a rate of
one (1) per second.
3. The LOWER RIGHT key pad is used to select or deselect options.
Start Operating Set-Up
PD Models: Insert access door key, turn, and lift to remove access door.
�
PR Models: Once the debit card reader is installed (according to the
�
reader manufacturer's instructions), the set-up mode can be entered
by inserting a set-up card (supplied by the reader manufacturer) into
the card slot. If a manual set-up card is not available, manual set-up
mode can be entered by removing connector AA1 on the circuit
board.
IMPORTANT: The console must not be opened unless power is first
removed from the washer. To access connector AA1:
� Unplug washer or disconnect power.
� Open console, disconnect plug on AA1, close console.
� Plug in washer or reconnect power.
The washer is now in the set-up mode.
Before proceeding, it is worth noting that, despite all of the options
available, an owner can simply choose to uncrate a new commercial
washer, hook it up, plug it in, and have a unit that operates.
SET-UP CODES
The LOWER MIDDLE key pad will advance from code to code.
�
The LOWER LEFT key pad will change the code value.
�
The LOWER RIGHT key pad will select or deselect options.
�
FOR PR MODELS: The set-up codes are the same as for the 'PD'
models except where noted.
The set-up code is indicated by the one or two left-hand characters. The
set-up code value is indicated by the two or three right-hand characters.
CODE
6 0 7 REGULAR CYCLE PRICE
6 0 7
Represents the number of quarters (coin 1); may adjust from 0-39.
(See VALUE OF COIN 1.) Advance from 0-39 by pressing the LOWER
LEFT key pad. Factory preset for 7 quarters = $1.75.
PR MODELS ONLY: Factory preset for 0 quarters.
� Press the LOWER MIDDLE key pad once to advance to next code.
EXPLANATION
CODE
7 1 1 WASH LENGTH
7 1 1
This is the number of minutes for WASH.
Choose from 8-20 minutes by pressing the LOWER LEFT key pad.
� Press the LOWER MIDDLE key pad once to advance to next code.
8 2 1 RINSE CYCLES
This is the length and total number of rinses. Each rinse agitation is
8 2 1
1-4 minutes, with a choice of 1 or 2 rinses. The middle digit is the
length of rinse agitation and the right digit is the number of rinses.
The number is changed in the following sequence (11, 21, 31, 41,
12, 22, 32, 42) by pressing the LOWER LEFT key pad.
Press the LOWER MIDDLE key pad once to advance to next code.
The DELICATES & KNITS cycle has a fixed rinse agitation length
of one minute.
� Press the LOWER MIDDLE key pad once to advance to next code.
9 0 0 CYCLE COUNTER OPTION
This option is either SELECTED 'ON' or NOT SELECTED 'OFF'.
9 0 0
Not Selected 'OFF'.
9 0 C
Selected 'ON' and not able to be deselected.
Press the LOWER RIGHT key pad 3 consecutive times
to select 'ON'. Once selected 'ON' it cannot be deselected.
� Press the LOWER MIDDLE key pad once to advance to next code.
1. 0 0 MONEY COUNTER OPTION
This option is either SELECTED 'ON' or NOT SELECTED 'OFF'.
1. 0 0
Not Selected 'OFF'.
1. 0 C
Selected 'ON'.
Press the LOWER RIGHT key pad 3 consecutive times
to select 'ON' and 3 consecutive times to remove
(Not Selected 'OFF'.) Counter resets by going from 'OFF' to 'ON'.
Selected 'ON' and not able to be deselected.
1. C 0
To select 'ON' and not able to be deselected, first select 'ON', then
within two seconds press the LOWER RIGHT key pad twice, the
LOWER LEFT key pad once, and exit the set-up mode.
� Press the LOWER MIDDLE key pad once to advance to next code.
2. 0 0
SPECIAL PRICING OPTION
This option is either SELECTED 'ON' or NOT SELECTED 'OFF'.
2. 0 0
Not Selected 'OFF'.
2. S P Selected 'ON'. Press the LOWER RIGHT key pad once
for this selection.
If SPECIAL PRICING OPTION is selected, you have access to codes '3.'
through '9.'.
� Press the LOWER MIDDLE key pad once to advance to next code.
OPTIONS TO USE IF SPECIAL PRICING IS SELECTED:
SPECIAL CYCLE PRICE
3. 0 7
3. 0 7
Represents the number of quarters (coin 1): may adjust
from 0-39. (See VALUE OF COIN 1.) Advance from 0-39 by
pressing the LOWER LEFT key pad. Factory preset
for 7 quarters = $1.75.
PR MODELS ONLY: Factory preset for 0 quarters.
� Press the LOWER MIDDLE key pad once to advance to next code.
EXPLANATION
11