Teledyne 6200A Manuals

Manuals and User Guides for Teledyne 6200A. We have 1 Teledyne 6200A manual available for free PDF download: Manual

Teledyne 6200A Manual

Teledyne 6200A Manual (206 pages)

TRS ANALYZER

Brand: Teledyne | Category: Analytical Instruments | Size: 3.05 MB

Table of Contents

Model 6200A Trs Analyzer Manual Addendum

2
Table of Contents

28
- 1 How to Use this Manual
  
  36
  - Safety Messages
    37
- 2 Getting Started
  
  38
  - Installation
    38
  - Electrical and Pneumatic Connections
    38
  - Initial Operation
    43
- 3 Specifications, Agency Approvals, Warranty
  
  52
  - Specifications
    52
  - Epa Equivalency Designation
    53
  - Warranty
    54
- 4 The 6200A so Analyzer
  
  56
  - Principle of Operation
    56
  - Instrument Description
    59
    
    Sensor Module, Reaction Cell, Detector
    59
    
    Pneumatic Sensor Board
    59
    
    Computer Hardware and Software
    59
    
    V/F Board
    60
    
    Front Panel
    60
    
    Power Supply Module
    63
    
    Power Switch
    63
    
    Pneumatic System
    63
- 5 Software Features
  
  64
  - Index to Front Panel Menus
    64
    
    Sample Menu
    66
    
    Set-Up Menu
    67
  - Sample Mode
    70
    
    Test Functions
    70
    
    CAL, CALS, CALZ, Calibration Functions
    73
  - Set-Up Mode
    75
    
    Configuration Information (CFG)
    75
    
    Automatic Calibration (Autocal)
    75
    
    Data Acquisition System (DAS)
    75
    
    Range Menu
    76
    
    Auto Range
    77
    
    Password Enable
    80
    
    Time of Day Clock
    80
    
    Diagnostic Mode
    80
    
    Communications Menu
    80
    
    Variables Menu (VARS)
    81
- 6 Optional Hardware and Software
  
  82
  - Rack Mount Options
    82
  - Zero/Span Valves
    82
  - Internal Zero/Span (IZS)
    84
  - Autocal - Setup of IZS and Zero/Span Valves
    84
  - Permeation Tube (Used with IZS Option)
    87
  - Ma, Current Loop Output
    90
  - Status Output
    90
  - Interface
    91
    
    Setting up the RS-232 Interface
    91
    
    Command Summary
    94
    
    TEST Commands and Messages
    98
    
    WARNING Commands and Messages
    99
    
    CALIBRATION Commands and Messages
    100
    
    DIAGNOSTIC Commands and Messages
    101
    
    DAS Commands and Reports
    102
    
    VARIABLES Commands and Messages
    105
- 7 Calibration and Zero/Span Checks
  
  108
  - Manual Zero/Span Check or Calibration through the Sample Port
    111
  - Manual Zero/Span Check or Calibration with Zero/Span Valves Option
    113
  - Manual Zero/Span Check with IZS Option
    114
  - Automatic Zero/Span Check
    114
  - Automatic Zero/Span Calibration
    114
  - Calibrate on so Permeation Tube
    115
  - Use of IZS or Zero/Span Valves with Remote Contact Closure
    115
  - Epa Protocol Calibration
    116
    
    Calibration of Equipment
    116
    
    Calibration Gas Sources
    117
    
    Data Recording Device
    119
    
    Dynamic Multipoint Span Calibration
    119
    
    SO Calibration Procedure
    120
    
    Calibration Frequency
    126
    
    Other Quality Assurance Procedures
    126
    
    Summary of Quality Assurance Checks
    128
    
    ZERO and SPAN Checks
    129
    
    Recommended Standards for Establishing Traceability
    130
  - Special Calibration Requirements for Dual Range or Auto Range
    131
  - Calibration Quality
    132
  - References
    133
  - Maintenance Schedule
    134
  - Replacing the Sample Particulate Filter
    135
  - Replacing the Permeation Tube (Option)
    137
  - Replacing the IZS Zero Air Scrubber (Option)
    137
  - Cleaning Orifice and Orifice Filter
    138
  - Cleaning the Reaction Cell
    139
  - Pneumatic Line Inspection
    139
  - Leak Check Procedure
    142
  - Light Leak Check Procedure
    143
  - Eprom Replacement Procedure
    143
- 9 Diagnostic, Troubleshooting
  
  144
  - Operation Verification - 6200A Diagnostic Techniques
    146
    
    Fault Diagnosis with TEST Variables
    146
    
    Fault Diagnosis with WARNING Messages
    152
    
    Fault Diagnosis Using DIAGNOSTIC Mode
    154
    
    6200A Internal Variables
    161
    
    Test Channel Analog Output
    163
    
    Factory Calibration Procedure (Quick Cal)
    164
  - Performance Problems
    166
    
    AC Power Check
    166
    
    Flow Check
    167
    
    No Response to Sample Gas
    167
    
    Negative Concentration Display
    168
    
    Excessive Noise
    168
    
    Unstable Span
    169
    
    Unstable Zero
    170
    
    Inability to Span
    170
    
    Inability to Zero
    171
    
    Non-Linear Response
    171
    
    Slow Response
    172
    
    Analog Output Doesn't Agree with Display Concentration
    172
  - Electronic Subsystem Troubleshooting and Adjustments
    173
    
    Computer, Display, Keyboard
    173
    
    Communications
    176
    
    Voltage/Frequency (V/F) Board
    179
    
    Status/Temp Board
    185
    
    Power Supply Module
    188
    
    Flow/Pressure Sensor
    192
    
    Reaction Cell Temp
    196
    
    Preamp Board
    196
    
    PMT Cooler
    196
    
    HVPS (High Voltage Power Supply)
    199
  - Optical Sensor Module Troubleshooting
    201
    
    Pmt
    201
    
    UV Lamp Adjust or Replacement
    201
    
    UV Filter Replacement
    202
    
    Shutter System
    202
  - Pneumatic System Troubleshooting
    203
    
    Leak Check
    203
    
    Pump
    203
    
    Kicker
    203
    
    Z/S Valves & IZS Permeation Tube Oven
    205

Advertisement

Advertisement

Related Products

Teledyne Categories

Measuring Instruments Analytical Instruments

Digital Camera

Digital Camera Test Equipment

Security Camera

Security Camera

More Teledyne Manuals