Table of Contents
Advertisement
Connecting the appliance
Important!
Check that the mains power supply voltage corresponds to
the value indicated on the rating plate on the bottom of the
appliance.
Connect the appliance to an efficiently earthed and correctly
installed socket with a minimum current rating of 10a only.
if the power socket does not match the plug on the appliance,
have the socket replaced with a suitable type by a qualified
professional.
Using the appliance for the first time
Please note :
•
Coffee has been used to factory test the appliance and it is
therefore completely normal for there to be traces of coffee
in the grinder. The machine is, however, guaranteed to be
new.
•
you should customise water hardness as soon as possible
following the instructions in the section "Setting water
hardness" on page 17.
1. Plug the appliance into the mains socket and place the
main switch on the back of the appliance in the i position
(fig. 1).
you must first choose the language (the languages scroll
through at intervals of about 3 seconds).
2. When "english" appears, press the OK button (fig. 2). once
the language has been saved, the message "engliSh SeT"
is displayed.
Follow the instructions indicated by the appliance:
3. "FILL TANK": remove the water tank, fill to the MAX line
with fresh water then replace in the appliance (fig. 3).
4. "inSerT WaTer SPouT AND press OK": Check that the
hot water spout is inserted on the nozzle and place a
container holding a minimum of 100 ml underneath (fig.
4).
5. press the OK button (fig. 2). "PleaSe WaiT" is displayed
and the appliance begins to deliver water from the hot
water spout.
The appliance ends the first start up procedure, then the
message "Turning oFF PleaSe WaiT" is displayed and the
appliance goes off.
The coffee maker is now ready for normal use.
Please note:
•
When using the appliance for the first time, you need to
make 4-5 cups of coffee or 4-5 cappuccinos before the
appliance starts to give satisfactory results.
TURNING THE APPlIANCE ON
Please note:
Before turning the appliance on, make sure the main switch on
the back of the appliance is in the i position (fig. 1).
each time the appliance is turned on, it performs an automatic
preheat and rinse cycle which cannot be interrupted.
The appliance is ready for use only after completion of this
cycle.
Danger of burns!
during rinsing, a little hot water comes out of the coffee spouts
and is collected in the drip tray underneath. avoid contact with
splashes of water.
•
To turn the appliance on, press the
The message "heaTing uP PleaSe WaiT" is displayed.
after heating, the message "rinsing" is displayed, together with
a progress bar which gradually fills as preparation progresses.
as well as heating the boiler, the appliance also heats the
internal circuits by circulating hot water.
The appliance is at temperature when the message indicating
the taste and quantity of coffee appears.
TURNING THE APPlIANCE OFF
each time the appliance is turned off, it performs an automatic
rinse cycle which cannot be interrupted.
Important!
To avoid damaging the appliance, always press the
button to turn off.
Danger of burns!
during rinsing, a little hot water flows from the coffee spouts
(only if coffee has been made).
avoid contact with splashes of water.
To turn the appliance off, press the button
appliance performs a rinse cycle then goes off.
Please note:
if the appliance is not used for an extended period, place the
main switch in the 0 position (fig. 6).
never place the main switch in the 0 position while the
appliance is on.
no rinse is performed if no drinks with coffee have been made
while the machine has been on.
MENU SETTINGS
When you access the programming menu by pressing the P button,
the following menu items are available: descale, Set language, energy
10
button (fig. 5).
(fig. 5). The
Hide quick links:
Advertisement
Table of Contents
Troubleshooting
