Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Hunter Ernest Hemingway Series
Summary of Contents for Hunter Ernest Hemingway Series
- Page 1 42746-01 • 04/26/07...
-
Page 2: Table Of Contents
Catalog/Model No.: ________________ We are proud of our work. We appreciate the opportunity to Serial No.: ________________________ supply you with the best fan available anywhere in the world. Date Purchased: _ __________________ Before assembling your fan, for your records and warranty Where Purchased: _________________ assistance, record information from the carton and Hemingway by Hunter® nameplate label (located on the top of the fan For reference also attach your receipt or a motor housing) on the front cover of this manual. copy of your receipt to the manual. READ AND SAVE THESE INSTRUCTIONS. Table of Contents 1 • Getting Ready .............4 2 • Assembling the Skirt ........5 3 • Assembling the Base ........6 4 • Assembling the Table ........8 5 • Assembling the Fan .........9 6 • Assembling the Light Kit ......10 7 • Completing Assembly .........11 8 • Operating and Cleaning Your Fan ..12 9 • Troubleshooting ..........13 © 2007 Hunter Fan Company® 42746-01 • 04/26/07 • Hunter® Fan Company... - Page 3 Step Title Important Information Read this entire manual carefully before beginning Warnings: installation. Save these instructions. • To reduce the risk of personal injury, assemble the fan according to these instructions, and use only the hardware supplied. • To reduce the risk of personal injury, do NOT bend the blade General & Location: attachment system when installing, balancing, or cleaning the fan. • Use ONLY Hunter® replacement parts. NEVER insert foreign objects between rotating fan blades. • This fan is intended for outdoor use ONLY. This fan is • To avoid possible electrical shock, before relocating your fan, suitable for wet locations. If the fan has been subjected disconnect the power by unplugging the power cord from the to extreme weather conditions, inspect before use. electrical outlet. • This fan MUST be assembled by three or more people. • To reduce the risk of electrical shock, keep fan at least 16 feet away Do NOT attempt to assemble this fan without from pools and spas. NEVER place the fan where it can fall or be assistance. pulled into a pool or hot tub. • Make sure the installation site you choose allows the • To reduce the risk of electrical shock, ALWAYS connect to an...
-
Page 4: Getting Ready
Step Title 1 • Getting Ready To assemble this fan, be sure each person can do the following: ATTENTION: • Connect electrical wires. This fan must be assembled by • Lift 50 pounds. three or more people. Do not If you need help installing the fan, your Hemingway by Hunter® fan attempt to assemble this fan dealer can direct you to a licensed installer or electrician. without assistance. Gathering the Tools This fan weighs approximately You will need the following tools for assembling the fan: 150 lbs. • Standard screwdriver • Phillips-head screwdriver • Allen Wrench (included) Assembling Multiple Fans? • 7/16” Wrench or pliers If you are assembling more than Checking Your Fan Parts... -
Page 5: Assembling The Skirt
Bolt small screw holes around the power cord channel and a notch in the inner edge. Align the four holes in the skirt section with the holes in the base stand where the power cord is located, Base Bolt 64193-02-247 then align the notch in the skirt (x 16) section with the raised tab on the base stand. Partially install four base bolts Base Stand to attach the skirt section to the base stand. To ensure proper spacing, do not tighten the bolts until all have been partially installed. Note: The remaining three skirt sections are identical and may be installed in any order. 2-3. Align the four holes in the next skirt section with four holes in the base stand. Partially install four base bolts. Repeat for the remaining skirt sections. CAUTION: Do not attempt to assemble fan without all four skirt sections. The fan may fall if a skirt section is not installed. Step 2-4: Skirt Hardware Needed: Section 2-4. Align the holes in each skirt bracket with the adjoining skirt section and partially install two skirt bolts. Repeat for all skirt sections. 2-5. After all skirt sections are properly aligned, Skirt Bolt securely tighten all skirt bolts and base bolts. 06548-01-247 Skirt Bolt (x 16) Skirt Bracket 42746-01 • 04/26/07 • Hunter® Fan Company... -
Page 6: Assembling The Base
3-2. Thread the power cord through the lower pole section and slide the lower pole onto the base stand. Align the holes in the lower pole segment with the holes in the Lower base stand and securely install two lower pole bolts Pole with nuts to stabilize. Section Hardware Needed: Hardware Needed: Lower Pole Bolt Lower Pole Lower Pole Bolt Lower Pole Nut 06551-10-247 06552-02-247 (x 2) (x 2) Steps 3-3 - 3-4: 3-3. Being careful to not damage the fan finish, slide the Hardware Needed: base cover onto the lower pole and let it rest on the base stand. 3-4. Holding both the base stand and base cover, carefully tilt the base assembly and rest the assembly on its side to access the bottom of the base. Align the two tabs on the base cover with the Tab Screw 74513-54-247 two holes in the base stand. Install two screws to (x 2) secure the base cover to the base stand. Screw 42746-01 • 04/26/07 • Hunter® Fan Company... - Page 7 Foot Screw assembly back to its upright position. 74510-27-247 (x 1) Preinstalled feet With Step 3-6: Spindle Spindle Cover Grommet Spindle 3-6. Note: The spindle is optional. The fan can be installed with only the spindle cover. Holding the grommet in place, slide the spindle (optional) and spindle cover onto the lower pole. Lower the spindle and spindle Base cover to rest on the base cover. Base Cover Stand Without Spindle Middle Pole Section Step 3-7: Hardware Needed: Power 3-7. Thread the power cord through the middle pole Cord section. Attach the middle pole section to the lower pole section. Align the holes and securely install three Pole Screw screws to stabilize. 06549-01-247 (x 3) 42746-01 • 04/26/07 • Hunter® Fan Company...
-
Page 8: Assembling The Table
Step Title 4 • Assembling the Table Step 4-1: Table 4-1. Being careful not to damage the pole finish, (with assistance from at least one other person) place the hole in the center of the table over the lower pole segment. Make sure that all four feet rest securely on a level area with a solid ground surface. Lower Pole Segment 42746-01 • 04/26/07 • Hunter® Fan Company... -
Page 9: Assembling The Fan
5-2. Align the holes in the blade with the holes in the blade iron and attach with three blade Blade Screw screws. Securely tighten the screws. 74510-27-247 Blade (x 15) Iron Step 5-3: Hardware Needed: Blade Iron 5-3. Partially attach each blade assembly to the fan with Screw two blade iron screws. When all blades are attached and properly spaced, securely tighten all screws. Blade Iron Screw 63755-06-247 (x 10) Step 5-4: Hardware Needed: Upper Switch 5-4. Unbundle the wires from the fan. Thread Housing the wires from the fan through the hole in the upper switch housing. Attach the upper switch housing to the fan using two Upper Switch screws. Housing Screw 74506-54-247 (x 2) 42746-01 • 04/26/07 • Hunter® Fan Company... -
Page 10: Assembling The Light Kit
Step 6-2: Hardware Needed: Screw 6-2. Pull the 9-pin plug connector through the side of the upper pole segment. Align the holes in the 9-Pin upper pole segment with the bosses in the upper Plug switch housing. Install four screws to secure the Con- upper pole segment to the fan. nector Boss Upper Pole Screw 74514-60-247 (x 4) Steps 6-3 - 6-4: Light Kit 6-3. Being careful not to damage the fan finish, Hardware Needed: slide the light kit onto the upper pole segment holding the grommet in place. Connect the 9-pin plug connector from the fan to the 9-pin plug Plug connector from the light kit. Connectors 6-4. Align the holes in the side of the light kit with the Switch Housing holes in the upper switch housing and securely Screw install three switch housing screws. 64555-05-247 (x 3) 42746-01 • 04/26/07 • Hunter® Fan Company... -
Page 11: Completing Assembly
7-2. Connect the 3-pin plug connector from the fan to the 3-pin plug connector from the base. Push the wires into the pole. Steps 7-3 - 7-4: Window Closed 7-3. Be sure no wires are pinched before Hardware Needed: closing the window. Rotate the upper pole segment 180 to align the screw holes and close the window. 7-4. Align the holes with the logo coverplate Pole Screw Screw 06549-01-247 and securely install two screws. Logo (x 2) Coverplate Upper Step 7-5: Pole Hardware Needed: Segment 7-5. Install the remaining screw behind the logo coverplate. Securely tighten all screws. Pole Screw 06549-01-247 Screw (x 1) 42746-01 • 04/26/07 • Hunter® Fan Company... -
Page 12: Operating And Cleaning Your Fan
8-1. Insert a glass shade into a fitter and tighten the Glass thumbscrews. Repeat for all shades. Install three A-19 Shade medium base 60 Watt max light bulbs. Bulb Completed Assembly 8-2. Install the plastic plugs into the remaining holes in the pole. If you chose not to install the table, you will need to install all the included plugs. 8-3. Plug the fan into an electrical outlet. 8-4. The fan pull chain controls power to the fan. The pull chain has four settings in sequence: High, Medium, Low and Off. • Pull the chain slowly to change settings. • Release slowly to prevent the chain from recoiling into the blades. 87” 8-5. The light pull chain controls power to the light. • Pull the chain slowly to change settings. 8-6. This fan operates in a downdraft direction only by blowing air downward (counterclockwise blade rotation) to cool the area with a direct breeze. Note: Do not use a water hose or pressure washer to clean this fan. 8-7. For cleaning finishes, use a soft brush or lint-free cloth to prevent scratching. A vacuum cleaner brush nozzle can remove heavier dust. Remove surface smudges or accumulated dirt and dust using a mild detergent and a slightly dampened cloth. You may use an artistic agent, but never abrasive cleaning agents as they will damage the finish. 42746-01 • 04/26/07 • Hunter® Fan Company... -
Page 13: Troubleshooting
4. Remove the shipping bumpers. 5. Ensure that the fan is plugged into a suitable GFCI outlet. Problem: Noisy operation. 1. Tighten the blade iron screws until snug. 2. Tighten the blade screws until snug. 3. Check to see if the blade is cracked. If so, replace all the blades. 4. Check and tighten the screws in the switch housing mounting plate and in the upper and lower switch housing. Problem: Excessive wobbling. 1. If your fan wobbles when operating, use the enclosed balancing kit and instructions to balance the fan. 2. Tighten all blade and/or blade iron screws. 3. Tighten all skirt and base screws. 4. Make sure all three rubber feet are installed under the base. Problem: Table wobbling. 1. Make sure that all fasteners are secure and that the table is on a level area with a solid ground surface. If you need parts or service assistance, please call 888-830-1326 or visit us at our Web site at http://www.Hunterfan.com. Hunter® Fan Company 2500 Frisco Avenue Memphis, Tennessee 38114 42746-01 • 04/26/07 • Hunter® Fan Company...