Temporarily Turning Off The Sound; Using The Sleep Timer; Night Mode; Surround Mode - Marantz SR8500 User Manual

(Using the remote control unit)
To adjust the tone, press the AMP button and
press the > button PAGE3 is displayed.
To adjust the bass effect, press BASS+ (D2) or
BASS– (D3).
To adjust the treble effect, TREB+ (D4) or TREB–
(D5).
Note:
• The tone control function can work in the AUTO
Surround, Stereo, Dolby Pro Logic IIx , DTS,
DTS-ES, and Multi Ch. Stereo mode.
TEMPORARILY TURNING OFF
THE SOUND
OK
LIP.SYNC
PREV MUTE MUTE
GUIDE
MENU EXIT
TEST CH.SEL SURR
1 2 3
7.1CH ATT SPK-AB
4 5 6
DISP OSD SLEEP
7 8 9
To temporarily silence all speaker outputs such as
when interrupted by a phone call, press the MUTE
button on the remote.
This will interrupt the output to all speakers and the
head-phone jack, but it will not affect any recording
or dubbing that may be in progress.
When the system is muted, the display will show
"MUTE" .
Press the MUTE button again to return to normal
operation.

USING THE SLEEP TIMER

LIP.SYNC
PREV MUTE
GUIDE
MENU EXIT
TEST CH.SEL SURR
1 2 3
7.1CH ATT SPK-AB
4 5 6
DISP OSD SLEEP SLEEP
7 8 9 9
THX
0
CLEAR MEMO
To program the SR7500 for automatic standby,
press the SLEEP button on the remote.
Each press of the button will increase the time
before shut down in the following sequence.
OFF 10 20 30
90 80 70 60
The sleep time will be shown for a few seconds in
the display on the front panel, and it will count
down until the time has elapsed.
When the programmed sleep time has elapsed,
the unit will automatically turn off.
Note that the SLEEP indicator on the display will
illuminate when the Sleep function is programmed.
To cancel the Sleep function, press the SLEEP
button until the display shows "SLEEP OFF" and
the SLEEP indicator will disappear.

NIGHT MODE

M
D1 D1
D2
D3
D4
USE PAGE 3
D5 D5
CH VOL
TUNER CD CD-R MD
TAPE AUX1 AUX2 AMP AMP
LIGHT
1 2
RC8500SR
Learning Remote Controller
To select the NIGHT mode, press the AMP button
and press the > button until PAGE3 is displayed.
Press the NIGHT (D1) button.
Selecting the Night Mode ON is effective in Dolby
Digital only, and it compresses the dynamic range.
This softens loud passages such as sudden
explosions, to help prevent disturbing others late
at night.
To turn off the Night mode, press the NIGHT
button again.

SURROUND MODE

40
50
The SR7500 is equipped with many surround
modes. These are provided to reproduce a variety
of surround sound effects, according to the content
of the source to be played.
The available surround modes may be restricted
depending on the input signal and speaker setup.
AUTO
When this mode is selected, the receiver
determines whether the digital input signal is Dolby
Digital, Dolby Digital Surround EX, DTS, DTS-ES,
DTS 96/24 or PCM-audio.
Surround EX & DTS-ES will operate for multichannel
source that has a Dolby Digital Surround EX or DTS-
ES auto trigger flag in the digital signal.
When a Dolby Digital or DTS signal is input, the
number of channels for which the corresponding
signal is encoded will be played.
Inputting a Dolby Digital two channel signal with
Dolby surround status automatically subjects that
signal to Pro Logic IIx movie processing before
play.
PCM 96 kHz source material can be played in this
mode.
Notes:
• When you use this mode with certain DVD and
CD players, performing operations such as "Skip"
or "Stop" may momentarily interrupt the output.
• When the signal is not decoded, the mode is
changed to AUTO mode automatically. Refer to
page 24 to confirm the available decoding mode.
THX
THX mode applies additional processing to Dolby
Digital, DTS, and Dolby Pro Logic multi-channel,
surround sources. The THX processing was
developed by Lucasfilm Ltd. to recreated the
sound of top-quality theater.
Use the THX mode for all movies on disc, tape or
broadcast. In this mode, THX Surround EX will not
operate in this mode.
THX SURROUND EX
In a movie theater, film soundtracks that have been
e n c o d e d w i t h D o l b y D i g i t a l s u r r o u n d E X
technology are able to reproduce an extra channel
which has been added during the mixing of the
program.
This channel, called Surround Back, places
sounds behind the listener in addition to the
currently available front left, front center, front
right, surround right, surround left and subwoofer
channels.
This additional channel provides the opportunity
for more detailed imaging behind the listener and
brings more depth, spacious ambience and sound
localization than ever before.
THX Surround EX will operate for any 5.1 channel
source whenever THX is active.
THX Surround EX is not available in the system
without surround back speaker(s).
Note:
• When playing Dolby Digital Surround EX-
encoded software in 6.1 channels, it is required to
set the THX Surround EX mode.
2 MODE
(Dolby Digital, Pro Logic II x MOVIE, Pro Logic
II x MUSIC, Pro Logic II x GAME)
This mode is used with source materials encoded
in Dolby Digital and Dolby Surround.
DOLBY DIGITAL
This mode is enabled when playing source
materials encoded in Dolby Digital.
Playing multichannel encoded 6.1 or 7.1-channel
Dolby Digital sources provides five main audio
channels (left, center, right, surround left and
surround right) and Low Frequency Effect
channel.
Dolby Digital EX decoding is not available in this
mode.
Dolby Pro Logic IIx brings the excitement of
surround sound to any stereo mix, while making
existing Dolby Surround mixes sound more like
discrete 5.1 channels Surround sound.
Dolby Pro Logic IIx has 3 modes. Please see
below.
Pro Logic IIx MOVIE
This mode provides 6.1 or 7.1 channel surround
sound from Dolby Surround encoded stereo movie
sound tracks.
Pro Logic IIx MUSIC
This mode provides 6.1 or 7.1 channel surround
sound from conventional stereo sources, analog or
digital, such as CD, Tape, FM, TV, Stereo VCR,
etc.
Pro Logic IIx GAME
Game mode restores the impact low-frequency
surround effects by routing them to the system's
subwoofer.
25