Basic Operation (Tuner); Listening To The Tuner; Preset Memory - Marantz SR8400 User Manual

BASIC OPERATION
(TUNER)

LISTENING TO THE TUNER

Frequency scan step for AM is selectable.
Default setup is 10 kHz step, if your country's
standard is 9 kHz step, Press TUNER button on
the remote more than 6 seconds. Scan step will
change.
Note:
• Preset memory for the tuner will clear by changing
this setup.
AUTO TUNING
SOURCE
3. 2. 1.
USE PAGE 2
R MEMORY TUNING TUNING F/P F/P MODE DOWN
S A/B MULTI MULTI SPEAKER 7.1CH INPUT AUX2
MUTE
DVD VCR1 DSS/VCR2 AUX1 CD-R TAPE CD TUNER TUNER
DIGITAL S-VID TUNER TUNER CD CD-R
TAPE AUX1 AUX2
LIGHT
1
RC1400
Learning Remote Controller
(Using the SR8400)
1.
To select tuner and desired band (FM or AM),
press the TUNER button on the front panel.
2.
F/P button on the front panel to display the
frequency.
3.
Press the TUNING or button on the front
panel for more than 1 second to start the Auto
tuning function.
4.
Automatic searching begins then stops when
a station is tuned in.
(Using the remote control unit)
1.
To select tuner and desired band (FM or AM),
press the TUNER button twice within two
seconds on the remote.
2.
Press the > button until PAGE2 is displayed.
3.
Press and hold the SCAN+ (D1) or SCAN–
(D2) button for 1 second or more.
4.
Automatic searching begins then stops when
a station is tuned in.
If tuning does not stop at the desired station, use
to the "Manual tuning" operation.
28
MANUAL TUNING
3. 2. 1.
DOWN
R MEMORY TUNING TUNING F/P F/P MODE
S A/B MULTI MULTI SPEAKER 7.1CH INPUT AUX2
MUTE
DVD VCR1 DSS/VCR2 AUX1 CD-R TAPE CD TUNER TUNER
DIGITAL S-VID
TUNER TUNER
TAPE
(Using the SR8400)
1.
To select tuner and desired band (FM or AM),
press the TUNER button on the front panel
2.
Press the F/P (Frequency/Preset) button on
front panel, to have the frequency appear on the
display.
3.
3.
M
Press the TUNING or
D1 D1
D2 D2
3.
(Using the remote control unit)
D3
1.
To select tuner and desired band (FM or AM),
D4
2.
press the TUNER button twice within two
D5 D5
seconds on the remote.
2.
Press the > button until PAGE2 is displayed
MD
3.
1.
Press the SCAN+ (D1) or SCAN– (D2) button
AMP
to tune in the deseired station.
2
DIRECT FREQUENCY CALL
PREV MUTE
GUIDE GUIDE
MENU EXIT
TEST CH.SEL SURR
1 1 2 2 3 3
7.1CH ATT SPK-AB
4 4 5 5 6 6
DISP OSD SLEEP
7 7 8 8 9 9
0 0
CLEAR MEMO
TUNER TUNER CD CD-R MD
TAPE AUX1 AUX2 AMP
LIGHT
1 2
RC1400
Learning Remote Controller
1.
To select tuner and desired band (FM or AM),
press the TUNER button twice within two
seconds on the remote.
2.
Press the GUIDE on the remote, display will
show "FREQ - - - -".
3.
Input your desired station's frequency with the
ten numbered keypad on the remote.
4.
The desired station will automatically be
tuned.
(FM) TUNING MODE (AUTO STEREO OR MONO)
SOURCE
3.
M
D1 D1
VOLUME
D2 D2
3.
D3
DOWN
G F/P MODE MODE
D4
2.
USE PAGE 2 AKER 7.1CH INPUT AUX2
D5 D5
MUTE S-DIRECT
CD-R TAPE CD TUNER
AUX1 INPUT
DIGITAL S-VIDEO VIDEO L
CD CD-R MD
1.
AUX1 AUX2 AMP
LIGHT
1 2
RC1400
Learning Remote Controller
When in the auto stereo mode, AUTO indicator will
be illuminated on the display.
The "ST" indicator is illuminsted when a stereo
broadcast is tuned in.
At open frequencies, the noise is muted and the
"TUNED" and "ST" indicators are not illuminated.
If the signal is weak, it may be difficult to tune into the
buttons. station in stereo. In such a case, press the MODE
button on the front panel.Or press the TUNER
button and press the the > button until PAGE1 is
displayed. Press the T-MODE (D4) button.
"AUTO" indicator is not illuminated, if FM stereo
broadcasts are received in monaural and the "ST"
indicator is not illuminated.
To return to auto stereo mode, press the MODE
button or press T-MODE button on the remote again.
AUTO indicator is illuminated the display.

PRESET MEMORY

2.
With this unit you can preset up to 50 FM/AM stations
in any order.
3.
For each station, you can memorize the frequency
and reception mode if desired.
AUTO PRESET MEMORY
1.
This function automatically scans the FM and AM
band and enters all stations with proper signal
strength into the memory.
5. 2.
AV SURROUND RECEIVER SR8400
SELECTOR
CLEAR CLEAR MEMORY MEMORY
SPEAKERS A/B MULTI
SELECT ENTER
TV DVD VCR1
STANDBY
POWER ON/STANDBY PHONES
1.
To select FM , press the TUNER button on the
front panel.
M
2.
While pressing the MEMORY button, press
D1
the TUNING
D2
D3
"AUTO PRESET" will appear on the display,
D4 D4
UP
and scanning starts from the lowest frequency.
USE PAGE 1
D5 D5
3.
Each time the tuner finds a station, scanning
will pause and the station will be played for
AUDIO R
CH VOL
five seconds.
TV DVD VCR DSS
During this time, the following operations are
TUNER TUNER CD CD-R MD
TAPE AUX1 AUX2 AMP possible.
The band can be changed by the TUNER button.
4.
If no button is pressed during this period, the
current station is memorized in location Preset
02.
If you wish to skip the current station, press the
TUNING
is skipped and auto presetting continues.
5.
Operation stops automatically when all 50
preset memory positions are filled or when auto
scanning attains the highest end of all bands. If
you desire to stop the auto preset memory at
anytime, press the CLEAR button.
MANUAL PRESET MEMORY
2. 4.
RECEIVER SR8400
CLEAR MEMORY MEMORY
SPEAKERS A/B MULTI
TV DVD VCR1 DSS/VCR2
S
(Using the SR8400)
1.
Tune into the radio station you desire (Refer to
the "MANUAL TUNING" or "AUTO TUNING"
section).
2.
Press the MEMORY button on the front panel.
2.4. 1. 3.
"– –" (preset number) starts blinking on the
display.
VOLUME
3.
Select the preset number by pressing the
TUNING
DOWN UP
TUNING TUNING F/P MODE
MULTI SPEAKER 7.1CH INPUT AUX2 (approx. 5 seconds)
MUTE S-DIRECT
4.
DSS/VCR2 AUX1 CD-R TAPE CD TUNER TUNER
Press the MEMORY button again to enter.
AUX1 INPUT
DIGITAL S-VIDEO VIDEO L AUDIO R
The display stops blinking.
The station is now stored in the specified preset
memory location.
button up.
button during this period, this station
3.
PREV MUTE
GUIDE
MENU EXIT
TEST CH.SEL SURR
1 1 2 2 3 3
3.
7.1CH ATT SPK-AB
TUNING TUNING F/P M
4 4 5 5 6 6
DISP OSD SLEEP
MULTI SPEAKER 7.1CH INPUT
7 7 8 8 9 9
2.
AUX1 CD-R TAPE CD
0 0
CLEAR MEMO MEMO
or button, while this is still blinking