Rear Panel; Fm Antenna - Marantz SR4003 User Manual

ENGLISH

REAR PANEL

q w e r
INPUT INPUT
VIDEO VIDEO
S-VIDEO S-VIDEO
FM ( ( 75 FM 75Ω Ω ) ) GND GND AM AM
ANTENNA ANTENNA INPUT INPUT
TV TV DVD DVD VCR IN VCR IN VCR OUT VCR OUT DSS DSS MONITOR OUT MONITOR OUT
L L SL SL C C SBL SBL
L L
R R
R R SR SR SW SW SBR SBR IN IN OUT OUT
( ( AUX 2 AUX 2) ) 7.1CH INPUT 7.1CH INPUT TV TV DVD DVD VCR VCR DSS DSS
AUDIO AUDIO
L L SL SL C C SBL SBL
R R L L R R
FRONT FRONT SURROUND BACK SURROUND BACK
R R SR SR SW SW SBR SBR S. SPEAKER B S. SPEAKER B
SPEAKER SYSTEMS : 6-8 OHMS SPEAKER SYSTEMS : 6-8 OHMS
PRE OUT PRE OUT
!5 !4 !3
q
FM antenna terminal (75 ohms)
Connect an external FM antenna with a coaxial
cable, or a cable network FM source.
AM antenna and ground terminals
Connect the supplied AM loop antenna. Use the
terminals marked "AM" and "GND". The supplied AM
loop antenna will provide good AM reception in most
areas. Position the loop antenna until you hear the
best reception.
w
7.1 CHANNEL or AUX2 INPUT
By connecting a DVD Audio player, Super Audio CD
multichannel player, or other components that has a
multichannel port, you can playback the audio with
5.1 channel or 7.1 channel outputs.
e
VIDEO IN/OUT
(TV, DVD, VCR, DSS)
These are the video inputs and outputs. There
are 4 video inputs and 2 video outputs and each
one includes both composite video and S-video
confi gurations. Connect VCRs, DVD players, and
other video components to the video inputs.
The 2 video output channels can be used to be
connected to video tape recorders for making
recordings.
8
t y u
1 1
INPUT INPUT
3 3
COMPONENT COMPONENT
VIDEO VIDEO
MONITOR MONITOR
OUT OUT
INPUT 1 INPUT 1 INPUT 2 INPUT 2
2 2
Y Y C C B B / / P P B B C C R R / / P P R R Y Y C C B B / / P P B B C C R R / / P P R R
IN IN
3 3 4 4
1 1 2 2
IN IN OUT OUT IN IN OUT OUT OPT OPT OUT OUT FLASHER FLASHER
TAPE TAPE CD/CDR CD/CDR DIGITAL IN DIGITAL IN DIGITAL OUT DIGITAL OUT REMOTE CONT. REMOTE CONT. IN IN
AC IN AC IN
AC OUTLETS AC OUTLETS
L L R R L L
120V 120V 60Hz 60Hz
SURROUND SURROUND CENTER CENTER SWITCHED SWITCHED
1.25A 150W 1.25A 150W
MODEL NO. SR4003 MODEL NO. SR4003
!2 !1 !0 o i
r
MONITOR OUT
This is a monitor output and each one includes both
composite video and S-video confi gurations. When
connecting two video monitors or televisions, be
aware that the OSD interface can be used with both
MONITOR OUT connections.
t
COMPONENT VIDEO INPUT/
OUTPUT
If your DVD player or other device has component
video connectors, be sure to connect them to these
component video connectors on the unit. This unit
has two component video input connectors to obtain
the color information (Y, C , C
B R
recorded DVD signal or other video component and
one component video output connector to output it
directly into the matrix decoder of the display device.
By sending the pure DVD component video signal
directly, the DVD signal forgoes the extra processing
that normally would degrade the image. The result is
vastly increased image quality, with incredibly life like
colors and crisp detail.
When the video convert function is enabled, video and
S-video images can be output to the COMPONENT
MOINTOR OUT jack.
y
REMOTE CONT. IN/OUT terminals
Connect to a Marantz component equipped with
remote control (RC-5) terminals.
u
HDMI INPUT/OUTPUT
This unit has 3 HDMI inputs and 1 HDMI output. The
input function can be selected from the OSD menu
system. (See page 21)
i
AC INLET
Plug the supplied power cable into this AC INLET
and then into the power outlet on the wall.
INPUT 3 INPUT 3 OUTPUT OUTPUT
This unit can be powered by 120V AC only.
o
Flasher IN
This terminal controls the unit from each zone.
Connect the control signal from a Keypad, etc.
!0
AC OUTLETS
Connect the AC power cable of component such as
a DVD or CD player to this outlet.
This outlet provides power only when this unit is
turned on.
Caution:
• In order to avoid potential turn-off thumps, anything
plugged into this outlet should be powered up before
this unit is turned on.
• The capacity of this AC outlet is 150W. Do not
connect devices that consume electricity more
than the capacity of this outlet. If the total power
consumption of the connected devices exceeds the
capacity, the protection circuit shuts down the power
supply.
!1
DIGITAL INPUT
These are the digital audio inputs and outputs.
This unit has 2 coaxial digital inputs and 2 optical
digital inputs.
The inputs accept digital audio signals from a CD,
) directly from the
DVD, or other digital source component.
This unit has 1 optical digital output.
The digital output can be connected to MD recorders,
CD recorders, or other similar components.
!2
Speaker outputs terminals
Seven terminals are provided for the front left,
front right, front center, surround left, surround
right, surround back left and surround back right
speakers.
Note:
You can use surround back speaker terminals as S
(Surround) SPEAKER B terminals, when you use no
surround back speaker.
!3
AUDIO IN/OUT (CD, TAPE, CD-R,
TV, DVD, VCR, DSS)
These are the analog audio inputs and outputs.
There are 6 audio inputs (4 of which are linked
to video inputs) and 3 audio outputs (1 of which
are linked to video outputs). The audio jacks are
nominally labeled for cassette tape decks, compact
disc players, DVD players and etc.... The audio inputs
and outputs require RCA-type connectors.
!4
Subwoofer Output
Connect this jack to the line level input of a powered
subwoofer. If an external subwoofer amplifi er is used,
connect this jack to the subwoofer amplifi er input.
If you are using two subwoofers, either powered or
with a 2 channel subwoofer amplifi er, connect a "Y"
connector to the subwoofer output jack and run one
cable from it to each subwoofer amplifi er.
!5
Preamp Outputs
(L, R, SL, SR, SBL, SBR, C)
Jacks for L(front left), R (front right), C (Center), SL
(surround left), SR (surround right), SBL (surround
back left) and SBR (surround back right).
Use these jacks for connection to external power
amplifi ers.