Basic Operation (Remote Controller) - Marantz SR4003 User Manual

ENGLISH

BASIC OPERATION (REMOTE CONTROLLER)

NORMAL MODE
(When operating Marantz AV equipment products)
This remote controller is preset with a total of 12 types
of remote codes, including Marantz TV (television),
DVD, VCR (VCR deck), DSS (satellite broadcasting
tuner), TUNER, CD, CD-R, DMP, TAPE (tape deck),
AUX1, AUX2, and AMP (amplifi er).
Learning is not necessary for Marantz products. You
can use these products without setting any codes.
1.
Press the SOURCE button.
For this example, press DVD.
Pressing the SOURCE button once changes
the remote control to the settings for the source
that was pressed.
To change the amplifi er on other source, press
the SOURCE button twice (double-click). The
code is sent, and then the amplifi er source
changes to DVD.
SETTING THE BACK LIGHT
Pressing the Light button located on the side of
the remote controller lights the remote controller's
backlight. Pressing the button again while the backlight
is lit lights the backlight for another 2 seconds.
To turn off back light, press and hold down the SET
and OFF button until SEND indicator blinks twice.
To turn on it again, press and hold down the SET and
ON button until SEND indicator blinks twice.
Initial is back light ON.
PRESET MODE
(When operating non-Marantz AV equipment
products)
This remote controller is preset with remote control
codes from AV equipment by other manufacturers.
The preset codes are TV, CD, DVD and DSS.
Settings can be made in one of two ways.
When the preset codes are set, the following codes
are contained in the source button of the remote
controller.
See the attached manufacturer number list for the
preset manufacturers, devices, preset numbers, and
other settings.
Remote controller Corresponding preset Device name
source name code
TV TV Television
DVD DVD DVD player
CD CD CD player
DSS SATELLITE Satellite broadcasting
tuner equipment
34
Importants:
• Some codes may be not match your equipment.
In this case, you can use LEARN mode to store these
codes.
• The preset codes do not cover full functions.
If you need extra function, use LEARN mode to
store extra function.
• Wen the batteries are getting weak, the preset
procedure is not successful.
PROGRAMMING WITH THE 4-DIGIT CODE
1.
1.
1.
Press and hold down the SOURCE button for the
appliance which should be controlled and press
SET button until the SEND indicator blinks twice.
Then back light fl ushes.
2.
Press the 4-digit code by numeric buttons for
appliance (code table at the end of this book)
When the procedure is successful, the SEND
indicator will blink twice.
Note:
If the indicator did not blink twice, then repeat steps 1
through 2 and try entering the same code again.
SCANNING THE CODE TABLE
2.
3.
2.
3.
5.
1.
Switch on the appliance which should be
controlled.
2.
Press and hold down the SOURCE button for
appliance which should be controlled and press
SET button until the SEND indicator blinking
twice. Then back light fl ushes.
3.
Aim the remote control at the appliance and
slowly alternate between pressing INPUT 3
button and the SOURCE ON/OFF button for the
appliance.
4.
Stop when the appliance turns off.
5.
Press ENTER button once to lock in the code.
CHECKING THE CODE
2.
1.
1.
1.
Press and hold down the SOURCE button for
appliance which should be controlled and press
SET button until the SEND indicator blinking twice
then back light fl ushes.
2.
Press the INFO button.
The SEND indicator will blink twice.
3.
To view the code for fi rst digit, press 1 once.
Wait 3 seconds, count the SEND indicator
blinks (e.g. 3 blinks = 3) and write down the
number.
Note:
If a code digit is "0", the SEND indicator will not
blink.
4.
3
Repeat step three more times for remaining
digits. Use 2 for the second digit, 3 for the third
digit, and 4 for the fourth digit.
RESETTING THE CODE
1.
1.
2.
1.
Press and hold down the SOURCE button
for appliance which should be controlled and
press SET button until the SEND indicator
2.
blinking twice.
Then back light fl ushes.
2.
Press the below codes to reset.
TV : 1000
3.
DVD : 2000
CD : 3000
4.
DSS : 4000
The indicator will blink twice.
Note:
After this procedure, the selected SOURCE button is
set initial code.