Husky HU80833 Operator's Manual page 13

CONNECTiNg high PRESSURE hOSE TO
TRiggER hANDLE
See Figure 7.
 Screw the collar on the high pressure hose into the
trigger handle inlet coupler by turning the hose collar
clockwise.
 Pull on the hose to be certain it is properly secured.
CONNECTiNg ThE high PRESSURE hOSE TO
ThE PUMP
See Figure 8.
 Align the collar on the threaded nipple on the pump.
 Insert the nozzle on the end of the high pressure hose
collar into the threaded nipple.
 Turn the collar clockwise to tighten the hose securely to
the pump.
 Pull on the hose to be certain it is properly secured.
ATTAChiNg iNJECTiON hOSE
See Figure 9.
Before detergent can be used with this machine, the injection
hose must be attached.
 Open the cap of your detergent container.
 Push the injection hose filter onto the end of the injection
hose. Insert the injection hose into your cleaning solu-
tion so the injection hose filter rests at the bottom of the
detergent container.
 Push the open end of the injection hose securely over the
fitting as shown in figure 9.
CONNECTiNg ThE gARDEN hOSE TO ThE
PRESSURE wAShER
See Figures 10 - 11.
The water supply must come from a water main. NEVER use
hot water or water from pools, lakes, etc. For ease of use,
a self-coiling garden hose is provided.
NOTE: When using the self-coiling garden hose, be sure
that the hose does not become crimped during use as this
may cause damage to the pump.
Before connecting the garden hose to the pressure
washer:
 Run water through the hose for 30 seconds to clean any
debris from the hose.
 Inspect the screen in the water intake.
 If the screen is damaged, do not use the machine until
the screen has been replaced.
 If the screen is dirty, clean it before connecting the garden
hose to the machine.
To connect the garden hose to the machine:
 If using a garden hose that is not self-coiling, straighten
the garden hose.
ASSEMBLY
NOTE: There must be a minimum of 10 feet of unrestricted
hose between the pressure washer intake and the hose
faucet or shut off valve (such as a "Y" shut off connec-
tor).
 With the hose faucet turned completely off, attach the
end of the garden hose to the water intake. Tighten by
hand.
 Wrap the garden hose hanger strap around the garden
hose to keep it close to the handle and out of the way.
iNSTALLiNg CLEANiNg DECK
See Figures 12 - 14.
To install the cleaning deck on the pressure washer:
 Connect the lower end of the high pressure water supply
hose to the cleaning deck by inserting the deck inlet plug
into the quick connect coupler on the water supply hose.
Push ends together until coupler snaps into position.
 Slide cleaning deck and pressure washer housing to-
gether until the connection is secure.
 Insert upper end of high pressure water supply hose into
trigger handle outlet coupler and push ends together until
coupler snaps into position.
To install the cleaning deck on the spray wand:
 Assemble the trigger handle and spray wand as described
previously in this manual.
 Insert cleaning deck inlet plug into the spray wand quick
connect coupler and push ends together until coupler
snaps into position.
wARNiNg:
To reduce the risk of injection or injury, only use the
cleaning deck on flat, horizontal surfaces. Never lift the
cleaning deck from the cleaning surface while operating
the pressure washer.
ADDiNg LUBRiCANT TO ThE ENgiNE
See Figure 15.
NOTE: This machine has been shipped with approximately
2 oz. of lubricant in the engine from testing. You must add
lubricant to the engine before starting it the first time.
CAUTiON:
Any attempt to start the engine without adding lubricant
will result in engine failure not covered under warranty.
 Place pressure washer on a flat, level surface.
 Unscrew the oil cap / dipstick by turning counter-
clockwise.
 Using 4-stroke engine lubricant (SAE 10W30), fill to the
upper level of the oil filter neck (18 oz., 4-cycle engine
lubricant provided).
8 — English