Table of Contents
Advertisement
C-1
FIELD INSTALLED OPTIONS / ACCESSORIES
K2641-2 FOUR WHEELED STEERAbLE YARD TRAILER
For in plant and yard towing. Comes standard with a Duo-Hitch™, a
2" Ball and Lunette Eye combination Hitch.
K2636-1 TRAILER - Two-wheeled trailer with optional fender and
light package. For highway use, consult applicable federal, state,
and local laws regarding possible additional requirements. Comes
standard with a Duo-Hitch™, a 2" Ball and Lunette Eye combination
hitch. Order:
K2636-1 Trailer
K2639-1 Fender & Light Kit
K2640-1 Cable Storage Rack
K1898-1 SPARK ARRESTOR - Easily mounts to standard muffler.
K704 ACCESSORY SET - Includes 35 ft. (10m) of electrode cable
and 30 ft. (9.1m) of work cable, headshield, work clamp electrode
holder. Cables are rated at 400 amps, 100% duty cycle.
K857 25 ft (7.6m) or K857-1 100 ft. (30.4m) REMOTE CONTROL
Portable control provides same dial range as the output control on
the welder. Has a convenient 6 pin plug for easy connection to the
welder.
K2467-1 - Digital weld meters kit with easy to read digital meters for
volts and amps. Easy to install.
K802N POWER PLUG KIT
Provides four 120 volt plugs rated at 20 amps each and one dual
voltage, full KVA plug rated at 120/240 volts, 50 amps.
K802R POWER PLUG KIT
Provides four 120 volt plugs rated at 15 amps each and one dual
voltage, full KVA plug rated at 120/240 volts, 50 amps.
T12153-9 50 AMP, 120/240V POWER PLUG (1-Phase)
T12153-10 50 AMP, 240V POWER PLUG (3-Phase)
K1816-1 FULL KVA ADAPTER KIT
Plugs into the 120/240V NEMA 14-50R receptacle on the case front
(which accepts 4-prong plugs) and converts it to a NEMA 6-50R
receptacle, (which accepts 3-prong plugs.) For connection of
Lincoln equipment with NEMA 6-50 Plug.
WIRE FEEDER OPTIONS
K2613-1 LN-25 PRO PORTAbLE WIRE FEEDER-The
MAXTRAC® wire drive enhances performance, while the
replacement case, and many other upgrade options that can
be installed in less then five minutes aid in the serviceability.
KP1697-5/64 Drive Roll Kit- Includes: 2 polished U
groove drive rolls, outer wire guide and inner wire
guide for solid core wire. (Used on LN-25 Pro)
KP1697-068 Drive Roll Kit- Includes: 2 polished U
groove drive rolls, outer wire guide and inner wire
guide for solid core wire. (Used on LN-25 Pro)
ACCESSORIES
KP1696-1 Drive Roll Kit- Includes: 2 V groove drive
rolls and inner wire guide for Steel Wires. (Used on
LN-25 Pro)
K449 LN-25 - Includes internal contactor for across the arc opera-
tion (no control cable). Provides "cold" electrode until gun trigger is
pressed. Includes gas solenoid.
K1870-1 LN-15 Across the Arc Wire Feeder.
Portable, lightweight, compact CC/CV unit for flux-cored and MIG
welding. Includes Gas Solenoid, adjustable flow meter and internal
contactor. For 10-15 lb. (4.5-6.8kg) spools.
Magnum Gun and Magnum Gun Connector Kit are required for gas-
shielded welding. Innershield Gun is required for gasless welding.
K126-2 Magnum 350 Innershield Gun
K1802-1 Magnum 300 MIG Gun (for LN-25)
K470-2 Magnum 300 MIG Gun (for LN-15, Includes Connector Kit)
K466-10 Connector Kit (for LN-15, K470-2)
K1500-1 Gun Receiver Bushing (for LN-15 & K126-2)
K487-25 Magnum SG Spool Gun
Hand held semiautomatic wire feeder. Requires SG Control Module
and Input Cable.
K488 SG Control Module (For Magnum Spool Gun)
The Interface between the power source and the spool gun.
Provides control of the wire speed and gas flow. For use with a
spool gun.
K691-10 Input Cable (For SG Control Module)
For Lincoln engine power sources with 14-pin MS-type connection,
separate 115V NEMA receptacles and output stud connections.
Note: See Wire Feeder IM manuals for appropriate Drive Roll and
Guide Tubes.
TIG OPTIONS
K1783-9 Pro -Torch® PTA-26V TIG Torch
Air Cooled 200 amp torch (2 piece) equipped with valve for gas flow
control. 25 ft. (7.6m) length.
KP509 Magnum Parts Kit for PTA-26V TIG Torch
Magnum Parts Kit provides all the torch accessories you need to
start welding. Parts kit provides collets, collet bodies, a black cap,
alumina nozzles and tungstens in a variety of sizes, all packaged in
an easy to carry reclosable sack.
K870 Foot Amptrol®
K963-3 Hand Amptrol®
K2535-1 Precision TIG 225 Ready-Pak(For AC TIG)
K2350-2 Invertec® V205-T AC/DC One-Pak™ Package
(For AC TIG)
PLASMA CUTTING
K1580-1 Pro-Cut 55
Cuts mild steel using the 3-phase AC generator power from the
engine driven welder. Accepts 3-phase or 1-phase input power.
Requires the K1816-1 Full KVA adapter kit, if connected for 1-phase
input power.
VANTAGE® 300
C-1
Hide quick links:
Advertisement
Table of Contents
