Table of Contents
Advertisement
C-7
MAGNETIC SEPARATOR (K58)
The K58 is a permanent magnet type separator
designed to fit the top of the standard fill funnel of the
continuous flux feed system.
The purpose of the separator is to remove magnetic
materials such as mill scale and any other extraneous
magnetic materials which may have been recovered
along with the flux to be processed.
It is important to remove these magnetic particles from
the flux which is to be reused in the continuous flux
feeding system.
If the magnetic material is not
removed, it will gather around the nozzle of the gun
and impede or shut off the flux flow when making rela-
tively long welds or when welding continuously. The
magnetic particles can also cause porosity in the weld.
Fit the magnetic separator into the funnel or hopper.
Pour the flux to be reclaimed into the top pan of the
separator. The separator is designed so that the flux
flows around three permanent magnets. The magnets
remove all magnetic particles.
become covered with their full load, they automatically
stop the flux flow. When the flux flow stops, remove the
separator from the funnel or hopper. Turn it over and
open the panel that covers the magnets. Remove the
magnetic particles by brushing or by using an air blast.
WARNING
WHEN USING COMPRESSED AIR BE CAREFUL TO
PROTECT YOURSELF AND OTHERS IN THE AREA
FROM FLYING PARTICLES.
NOTE:
The magnetic separator is used with all
Lincoln mild steel fluxes - 700 Series, 800 Series and
900 Series. Do not use the magnetic separator with
any stainless steel, alloy, or hardsurfacing flux except
H-535. The magnetic separator removes some of the
alloying elements from these fluxes, thus changing
their characteristics.
MECHANIZED HAND TRAVEL UNIT (K110)
Carries K114 Squirtgun along the joint at a preset trav-
el speed to help the operator make better welds 10 to
25% faster than with manual travel. Speed range is 7-
60 ipm (.18-1.5 m/min). Requires K161 Power Pack.
ACCESSORIES
SQUIRTMOBILE
Self-propelled trackless carriage carries K114 gun on
long welds for automatic welder economy without high
fixture costs. Requires K161 power pack.
MECHANIZED TRAVEL POWER PACK
(K161-CABLE LENGTH)
Includes travel mag-amp circuit required when using
either a K62 Squirtmobile or K110 mechanized hand
travel unit with a K114 gun.
source. Available with 25, 50, 75 or 100' (7.6, 15.2,
22.9 or 30.5 m) power pack to wire feeder leads.
Connect to the power source for input power. (Not suit-
able for use with the LN-9F.)
GAS SOLENOID KITS
K425
When the magnets
K437
POWER EXTENDED WIRE DRIVE (K392)
Permits extending gun and cable up to 80 feet from the
K357 LN-9 (code 8180 and higher).
ENCLOSED REEL MOUNTING (K304)
Used with the LN-9SE for welding at a distance from
the wire feeder. Includes a door for the wire reel hous-
ing and a hand crank. 50 and 60 lb. reels can be used.
EXTENSION ASSEMBLY (K307 or K308)
For LN-9NE or LN-9SE. K307 is a 22
extension cable. K308 is 45 ft. (13.7 m). Permits weld-
ing up to 60 ft. (18 m) from the wire reel.
FILLET GUIDE (K70)
Attachment simplifies horizontal fillet welding when
using the Mechanized Hand Travel Unit (K110).
LINC-FILL ™ GUIDES
A complete line for submerged arc and Innershield
available.
LN-9 Wire Feeder
®
(K62)
Mounts near power
Mounts inside K357 LN-9 model above code
9131.
Mounts outside all other LN-9 models.
C-7
1
⁄
ft. (6.9 m)
2
Hide quick links:
Advertisement
Chapters
Table of Contents
Troubleshooting
