Installation; Technical Specifications; General Description - Lincoln Electric LN-10 HEADS & CONTROLS IM587-B Operator's Manual

A-1
TECHNICAL SPECIFICATIONS – LN-10 Heads & Controls
SPEC.# TYPE
Speed
K1563-1,-3 10 Series 35-500 IPM
Std Drive Boom Mount (0.89-12.7 M/M)
K1563-2,-4 10 Series 55 - 825 IPM
Hi-Speed Boom Mount (1.40 - 21.0 M/M)
K679-1 Synergic 7F* 50 - 770 IPM
Std Drive Boom Mount (1.27 - 19.5 M/M)
K679-2 Synergic 7F*
Hi-Speed Boom Mount
K1559-1,-3 LN-10 35-500 IPM
Std Drive Bench Model (0.89-12.7 M/M)
K1559-2,-4 LN-10 55 - 825 IPM
Hi-Speed Bench Model (1.40 - 21.0 M/M)
SPEC.# TYPE INPUT POWER
K1562-1 ,-2 LN-10 40-42 Vac + 10%
Δ Δ
Control Controls 4.0 Amps 50/60 Hz (K1562-1)
6.0 Amps 50/60 Hz (K1562-2)
K1563-1 ,-3 10 Series
Δ Δ
Std Drive Boom Mount
K1563-2,-4
Hi-Speed
K679-1 Synergic 7F*
Std Drive Boom Mount
K679-2 Synergic 7F*
Hi-Speed Boom Mount
K1559-1,-3 LN-10 40-42 Vac + 10%
Std Drive Bench Model 4.0 Amps 50/60 Hz (K1559-1,-2) (519.7 mm)
6.0 Amps 50/60 Hz (K1559-3,-4)
K1559-2,-4
Hi-Speed
• Excluding Wire Reel
Δ Included with K1561-Series, LN-10 Boom Packages
*Synergic 7F wire drives use 4-roll drives with 2 driven rolls(Drive roll kits not common with 10 Series heads)

GENERAL DESCRIPTION

The LN-10 is a modular line of 42VAC input 4-roll wire feed-
ers. A single control with dual procedure presettability of
wire feed speed (in IPM or M/min) and arc voltage is used
with a single DC welding power source.
The LN-10 models have controls providing keypad or
remote selectability of either of two procedures.
The units offer 4 independently selectable gun trigger
modes for each procedure; cold feed, 2 step and 4-step trig-
ger and spot weld mode.

INSTALLATION

WIRE DRIVE OR WIRE DRIVE SECTION OF FEEDER
LOW SPEED RATIO
Wire Size
Solid
.025 - 3/32 in.
(0.6 - 2.4 mm)
.025 - 1/16 in.
(0.6 - 1.6 mm)
.025 - 1/16 in.
(0.6 - 1.6 mm)
--- ---
.025 - 3/32 in.
(0.6 - 2.4 mm)
.025 - 1/16 in.
(0.6 - 1.6 mm)
CONTROLS, HEADS AND COMPLETE UNITS
Dimensions
Height
14.80 "
(375.9 mm)
7.81 "
(198.4 mm)
11.5"
( 285.8mm)
20.46 "
Speed
Cored
.035 - .120 in .50 - 750 IPM
(0.9 - 3.0 mm) (1.25 - 19.0 M/M)
.035 - 5/64 in. 80 - 1250 IPM
(0.9 - 2.0 mm) (2.00 - 31.8 M/M)
.035 - 5/64 in. ---
(0.9 - 2.0 mm)
--- 80 - 1200 IPM
(2.00 - 30.5 M/M)
.035 - .120 in. 50 - 750 IPM
(0.9 - 3.0 mm) (1.25 - 19.0 M/M)
.035 - 5/64 in. 80 - 1250 IPM
(0.9 - 2.0 mm) (2.00 - 31.8 M/M)
PHYSICAL SIZE•
Width Depth
14.20 " 4.20 "
( 360.7mm) (106.7 mm) (8.2 Kg)
14.71 " 11.00"
(373.6 mm) (27.94 mm) (11.3 Kg)
7.16" 8.06"
(181.9 mm) (204.7mm)
14.73 " 30.35 "
(366.5 mm) (770.9 mm) (29.5 Kg)
Also, 4 selectable, presettable timers for each procedure;
preflow, postflow, burnback and spot weld time.
Arc starting can be optimized for each procedure with 5
selectable wire feed acceleration rates, and independent
control of slower run-in procedure.
A gas purge key is provided, as well as cold feed forward
and reverse keys with independently adjustable forward
feed speed setting.
LN-10
HIGH SPEED RATIO
Wire Size
Solid Cored
.025 - 1/16 in. .035 - 5/64 in.
(0.6 - 1.6 mm) (0.9 - 2.0 mm)
.025 - .045 in. .035 - .045 in.
(0.6 - 1.2 mm) (0.9 - 1.2 mm)
---
.025 - .045 in. .035 - .045 in.
(0.6 - 1.2 mm) (0.9 - 1.2 mm)
.025 - 1/16 in. .035 - 5/64 in.
(0.6 - 1.6 mm) (0.9 - 2.0 mm)
.025 - .045 in. .035 - .045 in.
(0.6 - 1.2 mm) (0.9 - 1.2 mm)
TEMPERATURE RATING
Weight Operating Storage
18.0 Lbs
25.0 Lbs
K-1563-1,-2
30.0 Lbs
K-1563-3,-4
(13.6 Kg)
+40°C +40°C
to
16.5 Lbs -20°C
(7.5 Kg.)
65.0 Lbs
K-1559-1,-2
70.0 Lbs
K-1559-3,-4
(31.8 Kg)
A-1
---
to
-40°C