Lincoln Electric LN-10 HEADS & CONTROLS IM587-B Operator's Manual page 35

C-4
K498
Magnum 200 FM GMAW gun and cable
assemblies are rated for 200 amps 60% duty cycle.
(Consult sales specifications for appropriate models)
K534
Magnum 250L FM GMAW gun and cable
assemblies are rated for 250 amps, 30% duty cycle.
(Consult sales specifications for appropriate models)
K478
Magnum 300 FM GMAW gun and cable
assemblies are rated for 300 amps, 60% duty cycle.
(Consult sales specifications for appropriate models)
K479
Magnum 400 FM GMAW gun and cable
assemblies are rated for 400 amps, 60% duty cycle.
(Consult sales specifications for appropriate models)
USING DUAL PROCEDURE WITH FAST-MATE
GUNS
There are a number of different options available for
using dual procedure with Fast-Mate guns. These
configurations are outlined below along with any addi-
tional required equipment.
Using Dual Schedule with Fast-Mate Guns
on -10 Series Feeders
Configuration 1
K489-7
Dual Schedule Fast-Mate adapter
K575
-Magnum 400 DS/FM gun (or competitive
DS/FM gun)
Configuration 2
K489-7
-Dual Schedule Fast-Mate adapter
K683-1
-Dual Procedure Switch (3 pin)
K686-2
-"Y" adapter (3pin + 5 pin to 5 pin)
K*-Non-DS Fast-Mate gun (Magnum 450WC,
Magnum 200, Magnum 300, Magnum 400, and
others)
K1558-1 REMOTE SWITCH INTERFACE
MODULE
The Module provides for user interface connection of
an external switch (flow switch, etc.) which must be
closed to enable the feeder welding operation. Also,
the Module provides for interface connection of exter-
nal equipment (fume extractor, etc.) to the Moduleʼs
isolated relay contacts which actuate when the feeder
welding gas solenoid is activated (representing weld-
ing operation in process).
ACCESSORIES
K1561-1 ROBOTICS INTERFACE
MODULE
The module plugs directly into the LN-10 control board
and provides an interface to a properly equipped
Fanuc robot. When installed and properly configured,
the K1561-1 Robotics Interface Module allows com-
plete control of the welding process from the robot
controller.
The Lincoln Electric Companyʼs Automation Center
should be contacted for questions regarding installa-
tion or operation of the Robotics Interface Module.
K1557-1 SWIVEL MOUNT
The K1557-1 Swivel mount attaches to the power
source. This kit includes a feeder adapter plate that
allows the feeder to rotate on top of the power source.
The feeder can be easily separated from the swivel
mount at any time. This option is compatible with the
K1556-1 Light Duty Caster Kit.
K1556-1 LIGHT DUTY CASTER KIT
This option provides 4 casters and all required hard-
ware to mount it to the Power Feed 10. This option is
compatible with the K1557-1 Swivel Mount.
K1555-1 INSULATED LIFT HOOK
For applications where an insulated lift hook is
required. This kit provides an easily installed, heavy
duty insulated lift eye that mounts to the wire reel
stand mast. See the instructions provided with the kit
for installation.
K1634-1 WIRE REEL ENCLOSURE KIT
The K1634-1 Wire Reel Enclosure Kit provides the
necessary parts to cover the wire and protect it from
excessive dirt and contamination. The kit is not for use
with 60lb coils (most 30 lb, 15kg, 44 lb fiber spools,
and smaller coils will work). The kit includes a 2 part
plastic reel cover, a Magnum conduit adapter for the
incoming end of the wire feeder feed plate, and a
short length of Magnum conduit to go between the
reel cover and the feedplate.
LN-10
C-4